View Full Version : Call me crazy,but would this work?
magis70
11-30-2002, 08:02 PM
The wheels in my head were spinning last night,and something occured to me,read this.
Could i construct an iso mod using one of those lpr tapeworm nipples,some microline,and a few fittings?Heres what i want to do.I want to take off the prv on my horizontal maxflow,replace it with a microline fitting,and run microline from there to the lpr nipple on the front of the gun,then take the prv and put it on the back of the gun where that other plug screw is.Im preety sure this would work,my only concern is if the microline will fit on the lpr nipple,im no sure its the same size as cocker hose,lets hear your comments guys.Yes i realize the hose could get in the way at times,but ill work around that,it would be a cheap *** mod,and be as good as a vff.
autococker ty
11-30-2002, 08:09 PM
probably not, the hoses would fukcing blow the **** off the maxflo.lol
I tried to do make an Iso-mod using the ndz lpr nibble and micro line and it didn't work for me because I couldn't get the microline over the nible. It is a very small diametter and is very hard so you can't just stretch it on there.
magis70
11-30-2002, 08:40 PM
What about this,buy 2 nipples,install 1 in the front,then hack off the other nipple in the middle,so it will thread into the prv hole,then just run cocker hose to each nipple?Now my question is,would that work,or do i ahve to plug off any air passages or anything like that to make it an iso mod.Ill show you what i mean by hacking off part of the nipple.
thebluenu
11-30-2002, 08:42 PM
uhhh, iv always thought "cocker hose" was "mircoline" - and if you have a tough time putting on the hosing put the end in your mouth and chomp on it (dont bite, just chomp), that will make it easier to put on......
1. Yes, It will work.
2. The hose is pretty flimsy, I wouldn't recomend it.
3. Cocker hose is not Microline.
magis70
11-30-2002, 08:56 PM
dang,i so wanted to try that:Poh well,lol.Someone needs to make a lpr nipple that takes microline hose instead,heh heh.Or better yet,macroline,ya,that be sweet.
Maxwell Murder
12-01-2002, 10:39 AM
Interesting
wolverine
12-01-2002, 06:45 PM
Check this link. I think it's what you are talking about. http://www.newdesignz.com/hot&new.htm
magis70
12-01-2002, 09:51 PM
too much dough for me man,im doing this mod for the sake that i dont have much money and im bored:)
Weasel00
12-02-2002, 07:45 AM
One thing you can do to get the microline to fit over the barb is to put a little heat to it. You just want to heat the part that is going over the barb. You also do not want to heat it to much or it will just come right off. Just heat it enough to make it a little softer and it should slide right on there.
Something else I have done is to go to a hardware store and get a plug for the hole in the front. You need a plug with a square head on it. Drill and tap that and insert a cocker barb there and then run your hose.
Jared
magis70
12-02-2002, 09:44 AM
What if i were to just run macroline from the maxflow prv hole to the front or rear air passage,do you think it might provide any kind of performance increase?
Weasel00
12-02-2002, 11:23 AM
No it probably would not. You need to some how cut off the air chamber going from the valve chamber to the solenoid chamber.
You can cut one of the valves to fit in where the prv goes and it will work. I did something similiar to my ESO when I put my VFF on my eclipse.
Jared
vBulletin® v3.6.4, Copyright ©2000-2012, Jelsoft Enterprises Ltd.