Can I screw with my Spyder to make is automatic?

[weasel]

Can I make my spyder se automatic just by screwing with it? Because once it went fully automatic while I was playing for a little bit.

[Counterfeit]

It did not go fully auto it was being starved for air so the sear would not catch. The same thing that happens when you run out of air with a spyder.

Not you cannot succesfully make it auto.

[weasel]

It wasn't when you run out of CO2 It fired like 3 or 5 balls right after one another and I just pressed the trigger once.

[Counterfeit]

Yeah, the sear was not catching like I said.

[weasel]

?????????

[Nemessis]

Shave the sear down, I dont recommend this because the hammer, valve and bolt will wear out very quickly and so will paint. You will need a 12v rev or an evulution in order to not chop paint

[Counterfeit]

Yes, but you see the problem is it will just chop your paint, not fire tham. That is why i said it cannot be really done succesfully.

[weasel]

Thanks a lot

[TLplus84]

if you are willing to go to the furthest places and spend massive amounts of money, you can get the ELCD grip frame for 240 dollars and make your gun full auto...but i think it's a waste..

[weasel]

I was never going to do it I was just gonna see if you could. plus if I had 240 bucks plus $200 (the cost of my gun with all the stuff I needed) I would save up some money and buy a real electric or an autococker.

[Silent Blur]

I was messing around with a spyder compact and made it fire full auto. The problem was it fired way too fast and chopped balls. I tried to slow down the speed by making the bolt heavier and it did slow it down a bit but it still fired too fast. Also the Co2 tank got extremely cold. I estimate the gun was firing some 25-30 shots per second. But like I said I would not recommend it. It will probably destroy the gun eventually.

[Predator2]

im not sure if it would work, but you can super glue a piece of metal to the metal thing sticking out the back of the trigger going under the sear completley. Maybe it would keep the sear level w/out it clicking and going back to normal and clicking after everyshot and as long as you hold it, it would fire full auto. Im not sure if it works but it is just a thought.

[A damn fool]

u cna shave donw the sear, and it will make it full auto. The only problem is, it will run full atuop form the second u pull the trigger, to the second u either take the tank off, or run oout of air. U will make a fullatuop p[aint blender, as ive herad it before. Do tlplus84's trigger job, and ull be able to make ur trigger 1/1t6th of an inch, and ull be bale to shoot fast ne wasy. Dont screw with ur gun to make it full atuo, ull end up messing it up

[RedWidow]

This happems to my gun all the time when im low on co2 or its really cold out I recomend not to continue playing like this because you chop a lot of balls, and you waste the rest of the co2, take the c02 off and warm it up, and if its low on c02 fill it up and check your o ring cause this usaully messes it up!

[TLplus84]

that's why low pressure is so great. you can run low on your tank and your gun won't burp. That's because when you're running low on Co2, then your gun doesn't have enough pressure to recock the gun. BUT when you're running lp, you don't need as much pressure to cock the gun, thus you can shoot on a low tank and still shoot fine.

[bowman57]

or if your just messing around, you can(take the beavertail off before you do this or youll really mess your finger up) push on the back of the bolt when you pull the trigger, itll shot about 5 balls full auto then uncock, youll have to recock the gun and to keep firing ful auto.

[A damn fool]

Thats awoms,e does it actually work? How far back do u hpld ur finger? Do the bals actully fire good, or like ****?

[bowman57]

its like when your running out of air except you have enough air to make the balls come out of the end of the barrel