Tigershark Mods

[joel]

Does anyone know any cool tigershark mods i can do to my tigershark? This is just my play around gun, so I wanna try and do anything with it really, any help would be much appreaciated, thankyou.

[Sid]

Get another used tigershark for cheap. Attatch them together side by side. Then but a wheel between the two pumps. Attatch the pumps to the wheel as on an old steam train. Attatch a crank. Double barreled gattiling gun. Of course yo need to attatch a lever to the triggers so that if you pull one, the other one isn't.

This is the general idea. The actual mechanisms need to be applied by you. Have fun.. let your imagination go wild.

[Skull]

I probably know just bout ne tigershark mod in the book ( seeing as how nearly half r on mine). Pick one of the subjects below and i'll post all the info u need...

battle pump grip
higher velocity adjustment
barrel porting
new paintjob
attatching a bottom line
attatching an expantion chamber
vertical feed
silencer
grenade launcher

got a ton more, but don't have the time to typem all.

Be prepared to tinker a lil. Some of these r gonna take a good amount of elbow greese, but if u luv ur shark as much as me its all worth it

[joel]

that is a wicked idea flash, i'd have absolutly no idea tho how to do that

ya the tigershark is a cool gun, i always use my pirahna tho, so the shark is getting no use at all and i dont want it to be a waste, so i wanna screw around with it and am thinking of actually taking it out when im doing all the mods i want to do with it..
I already attached a foregrip to the pump, so instead of pumping it with the actual pump, i do it with the foregrip, i like that better and it's more comfortable, and looks kinda cool
im actually intested in higher velocity adjustment, barrel porting, and silencer. I dont want to have to buy a new barrel for it tho. those should be good for now..
Thanks alot

[Skull]

Might wanna print this off ...

Porting the Barrel:

Start by removing the barrel and shroud from the Tigershark. Take the shrouds over to the trusty Craftsman band saw, and trim the tip e trim the rough edges with an Exacto knife and sandpaper, and your done!

Now for the fun part. I wrapped a 1/2" wide strip of paper around the barrel and mark the circumference. On Sid's Page, Sid mentions cutting 16 slots. Well, I figure 8 is enough. (In more ways than one!) So I fold the paper strip 8 times, to use as a guide to mark the slots. I wrapped it around the barrel again, 1/2" from the tip. I made a pencil mark on the barrel at each fold in the paper, and draw lines around the circumference at both sides of the paper. remove the paper, and draw straight lines between the marks. These were my cutting lines.

use a Dremel with a heavy duty cuttoff disc. (The heavy duty discs are slightly thicker than the standard discs. They don't break as easily, and cut wider slots.) Using plenty of cutting oil, and wearing safety glasses, cut through the barrel at each of the lines. I ended up going a little deeper, to get a larger opening in each slot, with the slots ending up about 3/4" long. Clean out the slots with a Exacto knife.

Now, to hone the barrel. Using a hone with 400 grit wet-or-dry sandpaper (which you wet with oil), and a trusty cordless drill, hone the inside of the barrel where the new slots were, running the drill in both directions, until it is smooth.

With a drill again, but this time with a trusty shotgun rod and swab, begin polishing with red automotive rubbing compound on a wet swab, again running the drill both directions. Polish the entire inside length of the barrel, until you have some really disgusting black goo coming out!

After washing THOROUGHLY both the swab and barrel, repeat the proccess with white automotive polishing compound. Again do the entire inside length, until again some really disgusting goo comes out! Wash everything again. Repeat the proces, until you have a very smooth, very shiny, almost mirror-like surface on the inside of the barrel.

For looks, use a rag with some polishing compound, and shine up the outside front of the barrel a bit, where it sticks through the shroud. Whether you cut your slots strait or angled is up to you.

K fingers are going numb, cant type nemore. I'll get back to ya on the velocity adjustment and silencer tomorrow...

[Sid]

I've seen some cool ideas for turning stingrays into Pulserifles, you know the guns the Marines use in Aliens.

Some people on this site will tell you that kinda stuff is stupid or lame, whatever. For rec games, do whatever you feel like. And really, what else are you going to experiment on?

With a little modding, you could take out the valve in the tiger shark and use it in a cannon, or mortar launcher. There's a million things you could do.

[AutocockerFreak]

Yeah arent we talking about paintball? Or do you wanna blow up your house next door with your grenade launcher?

[Sid]

Let me guess, you've never heard of a Scenario game? Geeze its just semantics.. haven't you ever seen paint cannons?

[Intimidation]

I have seen a semi-auto shark.I think that it was called the dark shark.The kit was like 120 dollars.get that and a Smart Parts big daddy barrel,and go scare the crap out of an angel:rolleyes:

[a11]

i need a barrel for under 50.00 bucks for my tigershark





PLEASE REPLY

[orly]

correct me if i am wrong but i dont think you can buy after market barrels for the tigershark, i have got a spyder barrel on my shark but i had to re thread the the gun for spyder threads. if anyone knows were you can buy after market barrels plz let me know.

[MikedaPber]

I know how to make a pump semi-auto.

Step one: get money

Step two: Buy an autococker.

lol. Sorry. But what were u saying about that pulse rifle stingray mod? I wanna do that to mine sence it wont get much attention next to a cocker.

[Darthmal2086]

Ok OK, Youv probably seen some good wheys to make the Cocking arm better. But iv gone the distance! Buy 2 of thos metal Cyrcles that when you screw them the cyrcle gets smaller. I think there made to tighten around copper piping. but a .99 cent gun at a thrift store, like a shquirt gun. Cutt off the handle and sprey it flat black! not atach it to ur Pumping arm with those 2 Thingies. If the Handle wont tighten correctly, Saw a slot on it so the little circle will fit and tighten it well. Ill try an provide a picturew, it should hellp alot. After You get done put alectrical tape around the metal Rings, So it doesnt look so ghetto. (=

The finished product costs less than 5$ AND looks professoinaly done. shoots almost 5 balls a second AND ACURATLY, if you have a butt plate on ur co2 tank. Heres a picture.

[Darthmal2086]

Ok OK, Youv probably seen some good wheys to make the Cocking arm better. But iv gone the distance! Buy 2 of thos metal Cyrcles that when you screw them the cyrcle gets smaller. I think there made to tighten around copper piping. but a .99 cent gun at a thrift store, like a shquirt gun. Cutt off the handle and sprey it flat black! not atach it to ur Pumping arm with those 2 Thingies. If the Handle wont tighten correctly, Saw a slot on it so the little circle will fit and tighten it well. Ill try an provide a picturew, it should hellp alot. After You get done put alectrical tape around the metal Rings, So it doesnt look so ghetto. (=

The finished product costs less than 5$ AND looks professoinaly done. shoots almost 5 balls a second AND ACURATLY, if you have a butt plate on ur co2 tank. Heres a picture.

[Darthmal2086]

Ok OK, Youv probably seen some good wheys to make the Cocking arm better. But iv gone the distance! Buy 2 of thos metal Cyrcles that when you screw them the cyrcle gets smaller. I think there made to tighten around copper piping. but a .99 cent gun at a thrift store, like a shquirt gun. Cutt off the handle and sprey it flat black! not atach it to ur Pumping arm with those 2 Thingies. If the Handle wont tighten correctly, Saw a slot on it so the little circle will fit and tighten it well. Ill try an provide a picturew, it should hellp alot. After You get done put alectrical tape around the metal Rings, So it doesnt look so ghetto. (=

The finished product costs less than 5$ AND looks professoinaly done. shoots almost 5 balls a second AND ACURATLY, if you have a butt plate on ur co2 tank. Heres a picture.

[Intimidation]

smart parts sells a "Big Daddy" barrel for the tigersgark.They may have others,too.

[mr.big]

boa,barrelsofamerica.com makes a barrel for the tigershark;)