H-e-l-p-!-!-!

[swfreak]

I'VE TRIED SEARCH BUT A DIRECT ANSWER WOULD HELP!

My gun had a tiny leak down the barrel so i took the whole thing apart and oiled every o ring.......EVERY o ring. When i put the gun back together and put teh co2 on it went total ape ****. Co2 was going in the asa and out the barrel at like full balst, yet i couldnt tell exactly where it was and when i cocked it a crazy suctioning sound happened. I took off the co2 and took everything apart again and tried once more. This time co2 even came out of the handle and made snow all over my room! WTF?! did i totally mess up the gun? I've now put it exactly as it is in the maual every part apart and cat find nething wrong..........HELP PLEASE!! SHould i replace all o rings even though they dont seem damaged? Where exactly is the cup seal because 2 look somewhat like one. THANKS FOR NEONE THAT HELPS!

[paintballer42o]

Did you check for any nicks on your nuts/bolts? You should probobly replace the o-rings.

[plushdragon]

well because you did not post what kind of gun i going to toss out some ball park help.ig you have a spyder/spyder clone stack tube blow back the cup seal/vavle is near the front of the gun near the asa.that little small extra piece under the barrel is where the cup seal sits.Moat guns you have to open that small tube and inside is the cup seal on a small pin.The brass vavle is held in by a screw and is covered by the grip frame.Some guns you have to take the grip frame off and uncrew one screw and then use a small wood dowel to poke it out towords the front of the gun.Most cup seal leaks is dirt or liquid c02 that froze the rubber cup seal.If you have a spyder there are 3 party cup seals that are 9.00 that will take dirt and co2 you would just need a pin that you can screw new rubber tip onto.

[Silverbolt]

I didnt read into your post much. I read you had a leak and you could hear it down your barel. I dont even know what kind of gun you have, or what anyone else said... frankly, I just, all of the sudden, got a head ache :/ The problem is your cup seal. Have it changed and you should be fine. You cant tell if your cup seal is bad by looking at it... just change it.

[Durandal]

Sounds like you may have lost the valve pin, or check the cup seal.

As for the CO2 out the handle, try oiling up the threads and oring then screw it in.

[pEnNyWiSdOm225]

Leaking down the barrel is almost always caused by the Cup Seal.

Take off the VA, find the little plasic thing that comes out and replace it with the extra from the repair kit that come with your marker.

[swfreak]

ok i have a Mokal Fokus 2. What is the valve pin? After looking through the manual what is the size of the cup seal? Is it really tiny, there is something called a Valve cup seal. Thats it right? Also something called a rear bumper looks pretty trashed, whats that? MY gun didnt come with a repair kit to my knowledge, (x mas present) so would a paintball store have one? thanks for the help.

[gffbrl21]

i think this is what you need, its for spyders but your gun is a spyder clone so it should work here yah go (http://http://www.xpaintball.com/spydfiraidki1.html)

[swfreak]

Thanks everyone for the help ill keep trying to get it fixed. The link doesnt work:-/ neway i could see what it is?

[mtdewpaintballr]

Originally posted by gffbrl21
i think this is what you need, its for spyders but your gun is a spyder clone so it should work here yah go (http://http://www.xpaintball.com/spydfiraidki1.html)

buddy your link dident work

[zeromiak]

probly just busted some o-rings, make sure evrything is together tight and no missing bolts or anything

[forumsk83r]

replace all o rings and cup seal, u should be fine

[tippmann_98_98]

Hey that happend to my old tippmann 98 custom one day i screwd on the co2 and it just started blasting from everywhere i found out i was missing a o ring. And when it was blasting out it broke amlost all of hte ohter o rings
i just replaced them all and it was FINE!!!:D

[butchcassady96]

you might not need to replace the cup seal

[Silverbolt]

Old post... RIP

[p41ntballjunkie]

you could try and take it to the local proshop, they should know what to do....i wouldt take it apart if i was new to pb...

[timmyfreaker]

Originally posted by tippmann_98_98
Hey that happend to my old tippmann 98 custom one day i screwd on the co2 and it just started blasting from everywhere i found out i was missing a o ring. And when it was blasting out it broke amlost all of hte ohter o rings
i just replaced them all and it was FINE!!!:D

http://img49.photobucket.com/albums/v150/timmyfreaker/Ownage/threadraisethedead_001.jpg