TES leak

[NiCk13136]

When i hook up the air to my tes it leaks majorly. It leaks as if the bolt wasnt cocked and i dont know where its coming from. I have new o rings on everything and takin a gun apart. Cup seal? i dont know but its really starting to piss me off. Sorry if i missed the anwser in a diff thread.. help?

[DarkeWolf]

bump.

maybe its from the vertical adapter?

[I'm_Addicted]

Check the sticky at the top of the page. It shows how to fix most TES problems.

[redlineIT228]

so what your saying is that it is leaking out of the barrel? if that is what you were saying, i had that same problem with my old spyder. i just went to a local shop and they fixed it up. it wasn't the cup seal though, and they didnt tell me what they did to it...*******s. but thats what i recommend

[NiCk13136]

allright I still havnt found what wrong with it so i mihgt jus take it in

[p8nter24]

The seal on your striker may be bad. Or the cupseal is bad. Take out your cupseal and see if the pin is screwed in all the way into it (I had this problem). Just never ever send it in to dragun or Odyssey. You will never see your marker again.

http://img.photobucket.com/albums/v251/Aero277/PBROOM%20SMILIES/drama.gif corn

[NiCk13136]

heh thats not true.... i had prob wit it in my 1 year warranty and sent it in and got it back 2 weeks later

[DarkeWolf]

Originally posted by NiCk13136
heh thats not true.... i had prob wit it in my 1 year warranty and sent it in and got it back 2 weeks later

did you send it in to them before or after the lawsuit against them? (no, I'm not being sarcastic, Im genuinely asking)

Asking cause a lot of peeps are having a LOT of probs getting any contact with the company at all right now. so am wondering if they are a lost cause, or if there is any hope at all.

[wolf'sRevenge]

the valve might be cracked (it happens) just replace the vavle

[p8nter24]

Really rare. You would be able to see it if it were cracked. But your best bet is to replace you valve/cupseal(i must agree). If should take any spyder one from a shop. If it still leaks then you striker could have a defect or sumpthin.

[middy4life29]

i accidentally broke my TES ball detent...i was wondering what thread ball detent it take...for example..autococker, spyder, timmy...i would greatly appreciate it if anybody knows...please reply ASAP

[Nugget359]

Did you take out your valve? You probably put it in backwards. Sounds like something that happened to me a while back with a piranha.

[NiCk13136]

allright well ive had this gun for about a year and never really looked at the manual to much for resembly because i knew where everything goes... but i dont know what the ****s called so is there an online manual print out anywhere? im nub i kno..
Well i still havnt found out whats wrong with it but when its uncocked it leaks majorly out of the barrel and uncocked it just leaks everywhere so i dont know where its leaking from. To get new cupseal...etc. is there a replacement kit for this kind of stuff?

[plugy]

Originally posted by middy4life29
i accidentally broke my TES ball detent...i was wondering what thread ball detent it take...for example..autococker, spyder, timmy...i would greatly appreciate it if anybody knows...please reply ASAP
i am pretty sure autococker ball detents work...i believe i have seen some topics about this

[NiCk13136]

allright well ive had this gun for about a year and never really looked at the manual to much for resembly because i knew where everything goes... but i dont know what the ****s called so is there an online manual print out anywhere? im nub i kno..
Well i still havnt found out whats wrong with it but when its uncocked it leaks majorly out of the barrel and uncocked it just leaks everywhere so i dont know where its leaking from. To get new cupseal...etc. is there a replacement kit for this kind of stuff?



any ideas?

[NiCk13136]

i meant when its uncocked it leaks out of the barrel and when its cocked it just leaks everywhere

[p8nter24]

Definitely your valve/cupseal assembly. Get a new one for around 20-30$. Any spider one should fit. Try to get a high flowing valve/cupseal.

Good luck.

[NiCk13136]

allright is this all i need to buy and it will have a better cup seal or is there a specific one i should buy.. http://corporate.marketworks.com/storefrontprofiles/processfeed.aspx?sfid=101468&i=52668050&mpid=6&dfid=1

[EVILDaddy07]

FORSHIZZLE!:laugh:

[NiCk13136]

is there a printable manual anwhere? ive seem to misplaced mine

[DarkeWolf]

pm me with your address and I'll make you a copy of mine and mail it to you

[NiCk13136]

allright well i dont know why but there is no cup seal star on the cupseal... would that be whats causing the leaks

[NiCk13136]

also is there a specific oring for the striker?

[NiCk13136]

will this be fine in the tes?
http://www.actionvillage.com/is-bin/INTERSHOP.enfinity/eCS/Store/en/-/USD/DisplayProductInformation-Start;sid=TbrGnV3iKbvG6R_GpysGNVdE6PpzQfJNPM8=?Pro ductID=xmKsFAY7CCcAAAD8quOLdoWL

[DarkeWolf]

wish I could be more help to ya on this, but I dunno. Feeling bad that more peeps are helping out on this one too :(

[TESballer]

Originally posted by NiCk13136
allright well i dont know why but there is no cup seal star on the cupseal... would that be whats causing the leaks
lost mine a long time ago nothing happened you don't need it
also is there a specific oring for the striker?
the rubber thing that comes on it stock is what you get, no replacement unless you buy the tes parts kit
will this be fine in the tes?
yes

[NiCk13136]

allright well....... i got new cup seal, star put in. I also put on a torpedo and macro. Put it all back together.. put the HPA on... and its still leaking. I have no idea what the prob now so I guess my last resort is to take it in..

[Brae]

Let me know what they said about your leak it sounds a lot like what mine is doing right now. I got some Laco cup seals im going to try tomorrow and ima ajust my reg and velocity il let you know if it fixes mine.:D

[Brae]

Nope my lapco cup seal didnt fix it but it does seam slower now. but still no deff answer yet.:confused:

[DarkeWolf]

I think that Nick got it answered somewhere in the kingman forums, or the low end electro forum...cant remember which.
you might PM him and see

[NiCk13136]

nah actually i didnt i still dont have any awnser i think im just gonna end up taking it to a shop and hopefully theyll have an awnser....

[DarkeWolf]

ah. I knew that you'd gotten some help with it over there, I thought that you had gotten it fixed :(

[p8nter24]

get a new valve/cupseal assembly. 20-30$, this is what fixed mine. I think I got a "new desinz" any spider one will fit.

[NiCk13136]

I have a new cup seal and i checked the valve and theres nothing to be wrong wit it. I have all new o rings on everything teflon taped up screw and front block i just dont see what could be the problem. The gun works fine i mean i can shoot fine when its leaking theres nothing wrong wit it its just the leaking. I dont see the possible cause of the leak either.

[p8nter24]

Did you replace all the orings on your bolt?? Try it.
Try replacing the orings on your valve also.

Good luck;)

[NiCk13136]

allready did that... i replaced alll orings with brand new ones

[NiCk13136]

allright so yesterday i gassed it up and it work.. it didnt leak. I dont know what happen from the week it sat on the desk but it fixed itself i guess. The only prob is after i shot bout 200 shots then it started to leak. The other problem i had was i couldnt walk it without it messin up. I would walk it and then it would kinda sputter and id have to recock the bolt.. whats the problem with this?