question to FOM

[Loherick]

do you have ready to be shiped:

-rat impulse/grey (color)
-12 revvy
-co2 20 w/anti-syphon

and how it will cost all this plus shiping to P.R. (Puerto Rico) next day if posible

thanks for the help !!!:D

[Ic3Floe]

yo, maybe your new but it would be best to either pm him or mail hi for these kinda questions!

[MuckRaker]

FOM and JohnnyRotten are at the SP factory in Pa., as we speak, birthing a new litter of Rats ... they probably won't be back until later today.

[Loherick]

well yea...

i am new....



what ? .... are you goin to shot me!?!?!

thanks for the advise :peace:

[MuckRaker]

FOM, my Bluegrass arrived today, it's much sweeter in person ... Gotta couple of questions.

1. How do you adjust the trigger and how do you determine the ROF ... don't want to outshoot my 12v revvy.

2. whats the best way to secure my hopper in the vert feed ... the fit is a bit loose.

3. did you use to seal the macro-line fittings, how do you loosen it. I've got a KAPP Drop Zone II with on/off asa that I want to use instead of the bottom line.

that's it for now ...

[Gibralter]

Lucky you Muck. I hope you enjoy the rat. The Bluegrass looks pretty sharp. I am breaking the 10th commandment now as we speak (coveting your neighbor's stuff) :P

[FOM]

Do me a big favor-- before you go mucking around with it, get some paint thru it?

There is nothing special required to remove the macro line fittings. If they are realy stiff, give them the old "hair dryer on hi" treatment for a few minunets to loosen it up.

I belive Jonney set that up with Walt doing the finel testing- so i know the Semi should be set about right. Don't pull it apart and much with it jutil you have tried it.

There are two adjustments on the trigger (well 3 if you count the tension) The vertical adjustment controles how soon the trigger fires, If this is too close you will get trigger bounce-- this sounds realy cool when firing air, but may not be so cool when shooting paint. The horzonal adjustment (part way down the trigger) controls overtravel. you can get the over travel down to almost nothing- but you may start missing shots in play as the Lever gets a little more flexy.

Please run a bunch of paint thru it befor you tighten up the trigger. We can makes thes guys supper short - but if we do when the gun is new, there is a very good chance that when the triggers starts to "settle in" the gun will stop shooting. We leave a little extra slop in there just for this resion.

When you do break it in, You need a 1.5mm allen wrench to adjust it.

Glad you got it Today- so are you impressed with our wonderful service <BMFG>

FOM

[unreal7]

I Am http://www.pbreview.com/forums/showthread.php?threadid=38832

[MuckRaker]

thanks FOM ... I shot about 150 rounds through it before I came to work ... just had to feel how it fired ... actually the trigger was good for me, I'm just curious about how to make adjustments ... I'll do the hair dryer thing if i can't get it off with a wrench. should be getting a case of paint thursday and i'll spend saturday sunday putting it through the paces.

[MuckRaker]

I went outside and shot another hopper ... I'd do more by my Snowbird neighbors haven't decided to hed back to Maryland ... I can't believe how well this gun works, the trigger is MUCHO lighter than i'd ever shot with ... Very quiet, especially compared to my Piranah. I put my KAPP on, no problem getting through the loc tite.

i'll post a pic soon.

[ferret]

Hi, i just wanna thank fom and johnny out loud too. I got my bluegrass today and its just pretty, especially with the cp lightning drop that they switched from the shocktech i originally ordered. Wont get a chance to gas it up until this weekend, but i cant wait. Thanks again!