HOLLAR IF YOU HEAR ME SHUTTER OWNERS

[NICKYB]

HEY I WANT PICS OF SOME SPYDER SHUTTERS WITH UPGRADES, especially new regs and stuff. SEND THEM IN FOR ME< ESpeciaally you * A DAMN FOOL*

[A damn fool]

Ill have someone bruing over a digital camera, and take one. As soon as i get a good pic, ill post it on the thread. I should have it posted buy next week. What ave u done to your shutter so far. and if u have a good pic, u should post it too

[TLplus84]

i'm not a Shutter owner..but can i hollar anyways ? hehe :P :D

[ptflyer]

when I am done with mine I'll post a pic...waiting for my genX reg to come in...and I have to get a dz2 ...all blue ano...to go on my red shutter....it will be red crome and blue....the all American Shutter.....

[TLplus84]

hey ptflyer that guns sounds like it's gonna be phat good luck with it :)

[ptflyer]

should have said what I have....here it is....

LP Shutter
magna valve
32o spring kit
Shocktech delrin bolt
drilled ASA
Hogue grips
custom trigger job
Crossfire 68/3000
(genX on it's way)

[TLplus84]

hey can you tell me how you drilled your asa via email? thanx

[ptflyer]

thanks TL..it didn't start that way ..was going to be all red...but when I went to get my bolt they only had blue...so I thought....ok...and went with it...I think it will look sweet also..we'll see...and I'll be sure to post that pic..when I am done...

[TLplus84]

man..now my gun sounds like **** compared to yours..DAMN IT~! hehe :P

[ptflyer]

LOL...ok..I sent you an e-mail....with the how to link....it explains it better than I can...and it has pics...can't get any easier....

[TLplus84]

PHAT thanx~ :D

[ptflyer]

wait til you drill it out..than thank me...watch your pressure...drop..and you velocity raise...wooooohooo........you will be pleasently surprised...I know I was...best mod I did....and it was FREE....

[TLplus84]

did you drill another hole in the ASA or did you make the stock hole bigger? And did your lpc come off? cuz i'm having a tough time getting mine off.

[ptflyer]

yes..the LPC comes off...just use the strong arm method...and I just drilled out the hole that were there...I thoght that was enough...others have told me to drill more....but this worked just fine....

be sure to read his instructions...and drill in the direction he tells you so you don't screw up the treads...and also...becareful of the mounting screw hole..that you don't drill on a angle and put a hole in the bottom of that mounting screw hole....he eaplains that in his directions...

[ptflyer]

oh..and you need to drill both..the hole from the LPC to the valve chamber...and the hole from the tank or reg side up to the LPC...

[ptflyer]

hey TL ..I just found this tread...you should check it out..this is a high flow ASA if I ever saw one....

there is a pic if the holes in an AKA..asa...

making me think...

[ptflyer]

hey TL ..I just found this tread...you should check it out..this is a high flow ASA if I ever saw one....

there is a pic if the holes in an AKA..asa...

making me think...
http://forums.paintballcity.net/showthread.php?postid=906615#post906615

[TLplus84]

im' still confused...so when i am finished, i should have 4 holes? 2 for the ASA part and 2 for the LPC hole?

[ptflyer]

no.there are two hole already......one from you tank or reg to the LPC.....and there is one from the LPC side to the valve chamber side...you want to make these two hole bigger...thats all...
but that link to the AKA pic..you will see what AKA does to a ASA...

[TLplus84]

OHH cool thanx for clafifying that

[BLiNDMAN]

well i finally went and drilled out my ASA...but haven't got a chance to try it.. hope i don't have any problems

[BLiNDMAN]

flyer we almost have the same setup... the only difference is : i have a stock bolt minus the venturi..madman spring set... as for the reg i was gonna get the gen x but can't afford to get anything new yet...so i probably will go with somethin cheaper

[ptflyer]

I just pick the genX becuse it looks cool and I am using N2....if you are using N2 and don't want to spend that much the Vigilante is a good reg for that.. For Co2, the best is the Palmer's stabalizer

[A damn fool]

ptflyer, ur shutter sound sweeeeet. All i did to drill out my asa was take a 3/16 bit, and ril, but it was a pain in the ***, because the original hole starts at the wall, and it was a pain to hold the drill steady. Do u think it would work even better though if i aded a few more holes around the edges, like 4, in a square effect?. How mcuh would u thik that will drop my pressure.

Upgraded shutters kick ***!!!

[ptflyer]

I don't know if it will drop it anymore...but if you go up in the tread ..there is a link to a page that shows the AKA asa....and look what there asa looks like....they have just one HUGE hole from the bottle/regulator side up to the LPC..and about 6 holes from the LPC to the valve chamber...that pic made me think...but I haven't decided if I am going to try that...I already have my shutter down to below 300..(I run it at 350psi or so..though)...just doing what I have done already...

[A damn fool]

I htink ill do that with the 6 holee in the lpc chamber, but how does that big hole allow the pin to be pushed down if u run veritcal. If i drilled out a nother huge whole, then i wouldnt ever be able to run a verical bottle, right?

[ptflyer]

no..you won't be able to run your bottle vertical..if you drill the larger hole on the bottom...but if you drill a hole that big..you better be running LP...so you would need to have a regulator somewhere in line anyway...and if you ever decide to go back..(don't know why you would)...you will have to get a replacement ASA..

[A damn fool]

what if i did it like they did it n the lpc side, and put like 6 holes, but kept the pin there just in case i ever neded to run vertical for a day? Will drilung it out that much really decrease my presure, or not?

[TLplus84]

hey how do you put the drill up against the wall? won't it mess up the threads of the ASA?

[A damn fool]

u send it to work with ur dad and have him have someone else do it, thats how, lol. I think though im just gonna have them add a few more holes in it around the asa end, and then a few more through the lp side.

[ptflyer]

well I drilled it starting from the vavle chamber side and drilled through to the LPC side...and stop befor you reach the treads for the LPC..I did mine on a drill press...but I supose you can do it with a hand drill...if you just take your time..and don't rush the drill bit through.(let the drill do the work)...and stop before the drill bit reaches the threads..hope you understand what I was trying to say..

[A damn fool]

What about going through the veritcal side though, im probably gonna have someon else do it, but im just wondering?