Paintball Forums

Paintball Forums (http://www.pbreview.com/forums/index.php)
-   Diablo (http://www.pbreview.com/forums/forumdisplay.php?f=65)
-   -   Wrath Faq (http://www.pbreview.com/forums/showthread.php?t=327544)

I'm_Addicted 08-03-2005 08:41 PM

Wrath Faq
 
Diablo Wrath General Maintenance

Lubricants: Do not use lightweight liquid paintball marker oil in the Wrath. Paintball oil is best used in blowback markers to lubricate the hammer, which is a large steel cylinder sliding rapidly within the aluminum marker body. O-ring greases are best suited for the Wrath’s many small o-rings throughout the gun. Dow 33 grease, also known in paintball as Shocker grease, works well. Also, Battle Lube grease is very good, has a lower viscosity than Dow 33 (which means it’s more slippery), and lasts longer between applications.

HPR: Apply a liberal coating of grease to the HPR large aluminum piston. It is accessed by removing the bottom half of the regulator from the top half, then grabbing the end (inside the bottom half) with small pliers and pulling out. Be sure to insert the aluminum piston back into the regulator bottom the correct way, with the cupped tip of the piston facing up toward the top half of the regulator.

LPR: Apply a liberal coating of grease to the o-rings on the LPR’s large brass piston, as well as to the small o-ring on the long skinny brass piston. Each piston is accessed from opposite ends of the LPR. It is necessary to remove the LPR valve retaining nut from the threaded end of the LPR body to access the long skinny brass piston. This retaining nut has a small amount of Loctite applied to keep it in place. The LPR body should be removed from the gun, and the low-pressure hose fitting should be unscrewed from its side before placing the LPR body into a vice. Wrapping a thin towel or old t-shirt around the LPR body before putting it into the vice and clamping securely should prevent any scratching or marring to the LPR’s exterior surface. When reinserting the retaining nut, it is not necessary to apply Loctite. Make sure the retaining nut’s ground face is inward making contact with the spring, and that the retaining nut is as close to flush with the end of the LPR body as possible. Hand tightening the retaining nut is sufficient.

LPR Adapter: It is not necessary to remove the LPR adapter, held in by one M5x12 screw in the body in front of the vertical ASA, to perform regular maintenance. The only time it is necessary to remove this adapter is to access the cup seal and main valve. Be sure when reinserting the LPR adapter that you apply a small amount of grease to its two o-rings, and do not cut the o-rings when they are passing the mounting screw hole.

Solenoid/Low-Pressure Valve Assembly: Disassemble the Low-Pressure Valve Assembly from the Solenoid and grease all four o-rings inside. The two inner o-rings on the brass carrier make contact with the plunger piston which controls air flow, and should receive a liberal application of grease. The outer o-rings on the brass carrier are stationary and only need a small amount of grease to ease reassembly. When reinserting the carrier into the valve body, position one of the side air exit holes inline with the hose fitting in the valve body. When reinserting the plunger piston into the carrier, be sure the piston goes in with the grooved end in first. When reinserting the Solenoid/Low-Pressure Valve Assembly back into the trigger frame, make sure the Solenoid/Low-Pressure Valve Assembly is pushed as far forward toward the trigger switch as possible when tightening down the two set screws. If the Solenoid/Low-Pressure Valve Assembly comes loose or the solenoid plunger is in contact with the trigger frame, it may not permit the Low-Pressure Valve’s plunger piston to close and create a proper seal. This may cause a small leaking sound, or may even cause the bolt to rapidly cycle when the marker is first aired up.

Ram: Apply a liberal coating of grease to the o-ring on the small end of the ram.

Bolt: Keep the bolt clean and dry at all times. It is unnecessary to grease the bolt. Grease on the bolt will collect dust particles from the air and cause scratching of the inner surface of the body.









CURRENT UPGRADES & MODS:

Custom Anodizing:
www.precisionpb.com They ano an entire marker for $60 or a per-peice price of $7.50 and do GREAT work. They also do color matching, so send in a paint chip or color sample and get great results.

Wrath Aftermarket Parts:
Alamo City Paintball: www.alamocitypb.com
Bolts, Cup Seals, Bolt Pins, more soon

FBM Delrin Wrath Triggers:
www.fbmfactory.com

Trigger Mod:
http://www.pbnation.com/showthread....t=&pagenumber=1

Trigger Switch Mods:
http://www.pbnation.com/showthread....threadid=856551
http://www.pbnation.com/showthread....hreadid=1022251

Trigger Guard Mod:
http://www.pbnation.com/showthread....threadid=894727

Aftermarket LPR Adapter:
The Wrath and O3 share many parts, and the LPR adapter is one of them, so if you have the mind to put on an aftermarket LPR, pick up the Zenitram O3 LPR adapter for $15 and an Autococker compatable LPR.
http://www.zenitram-mfg.com/ (Odyssey Upgrades>O3 LPR adapter)

Delrin Bolts:
http://zoompaintball.com/ (Sells BLACK delrin bolts)
http://www.pbnation.com/showthread....threadid=846394
www.spudnukl.com

PROS: Self-lubrication. Roughly 27 grams.

Nylatron Bolts:
http://www.pbnation.com/showthread....threadid=896352

PROS: Self-lubrication. Roughly 25 grams.

TFE Teflon Bolts:
www.spudnukl.com

PROS: Self-lubrication. Roughly 50 grams.

Wrath T-board:
http://www.scenariodreams.com
http://www.pbnation.com/showthread....threadid=855370

Custom Triggers:
Do a search for pbnation users: Comcast and THE BETTERONE

Air Ram Mod:
http://www.pbnation.com/showthread....threadid=864525

Autococker Vertical ASAs:
https://secure1.nexternal.com/share...ount2=979987740
(Scroll down- Straight and 15* ASAs with or without gauge ports)

Wrath Lord 08-04-2005 06:38 AM

Congrats.... Now hopefully we wont have so many stupid questions which have already been asked millions of times! Worthy of Stickyness if ever i saw one!

pyromonkey 08-04-2005 01:34 PM

nice thread, but you didnt just copy and paste this from pbnation did you? lol

I'm_Addicted 08-04-2005 02:39 PM

Quote:

Originally posted by pyromonkey
nice thread, but you didnt just copy and paste this from pbnation did you? lol

no:eyes: , I copied/pasted to Word and then to here:eyes:. We needed this though.

SKI008 08-05-2005 03:14 PM

Most of your links don't work.

pyromonkey 08-06-2005 04:24 PM

Quote:

Originally posted by I'm_Addicted



no:eyes: , I copied/pasted to Word and then to here:eyes:. We needed this though.

so you copied from pbnation to word to here???
w/e
still a good thread to help out a lot of ppl here.

btw, i didnt mean to offend you or anything i was just curious:)

fred1 12-11-2005 01:29 PM

i read at the top it said no oil but would it be allright to put some in the ASA from time to time like other guns?
thanks

brunedog 12-11-2005 04:56 PM

er. you should make this a stickie and get some new links:rolleyes: . Really need an upgrade stickie for this forum.

paint123 12-11-2005 11:15 PM

Quote:

Originally Posted by fred1
i read at the top it said no oil but would it be allright to put some in the ASA from time to time like other guns?
thanks

u should never put oil in the asa of any gun

fred1 12-12-2005 08:14 AM

Quote:

Originally Posted by paint123
u should never put oil in the asa of any gun

wow, really! thanks alot for that info.

paint123 12-12-2005 03:56 PM

np, just helping a fellow baller

Zofarr 12-12-2005 04:12 PM

Hmm most of the links don't work

Lopez17 12-13-2005 03:20 AM

Be sure to go into the post and give credit to the original author and cite where it came from.

Stickied.

ragezeon 12-17-2005 11:07 AM

most of the links are not active anymore

coffin_stuffer 12-25-2005 08:25 AM

is there a way to put internal hoses lyk the new wrath LTD? and can u replace the feedneck, if so, what fitting do i look for?

thnx. nice thread

punkp8ntballer 12-28-2005 04:34 PM

teflon or delrin???
 
I just got my wrath and I want a new bolt that will improve the accuracy and speed and stop the chopping in my gun will any bolt do that and would teflon or delrin be a better material????????????????????

paint123 12-29-2005 11:13 PM

either works, its mostly preference, delrin is just lighter than teflon, so u reduce kick more

jp_paintballer 01-17-2006 02:35 PM

hey, i just bought your diablo wrath and i was woundering if you could send me a few stickers to put on my gear.

thanks

nativetool 03-06-2006 06:10 PM

wrath replacement eyes
 
hi. i broke my eyes for my wrath and i was wondering what kind of replacment ones do i need ? where can i get these?

o state 03-09-2006 06:01 PM

i think u can get some from acp's website but im not sure... maybe not.

i dunno


All times are GMT -8. The time now is 08:35 AM.

Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.