pbReview.com - Paintball Reviews and Paintball Fields

  Join pbReview.com  |  Log In  
pbReview.com - Paintball Reviews and Paintball Fields

Search:

  
Home     |     Paintball Articles     |     Paintball Videos     |     Paintball Gear     |     Paintball Fields     |     Paintball Stores     |     Hot Deals     |     Paintball Forums     |     Chat
Go Back   Paintball Forums > Specific Marker Forums > Dye Precision


 
 
Thread Tools Display Modes
Prev Previous Post   Next Post Next
Old 06-04-2004, 09:00 AM   #1
Blue Baller
Registered User
 
Blue Baller's Avatar
 
Join Date: Jul 2003
Taking apart and lubing your bolt

This thread will tell you exactly how to disassemble your bolt kit and re-lube it.
First you need to take out that bolt kit. Heres what an image/red bolt kit will look like.



1. Unscrew the screw on the back plate, remove that, the back plate, and the breech in the front.

2. Take a 1/4 standard size allen wrench, and unscrew the back plug that is now visible.

3. Remove the o-ring on the front of the bolt that was exposed when you took off the breech (careful, don't damage it!), and gently push the bolt out from the front. Once you have pushed it as far as you can, pull it very gently from the back.

4. Remove the rear wall, the bolt stop, the sleeve, and the top hot, all respectively. Set these aside.

5. You'll notice that the beer can and the front wall in the picture are still inside the gun. To get these out, I like to take my barrel, put a piece of cloth in front of it, and push them out from the front using the barrel. Also set these aside.

6. Now, your enitre bolt assembly is set aside. Take somthing soft, such as an old white t-shirt, and wipe down all the old lube. Make sure you get as much of it as possible. Concentrate on the o-rings as well. Do not use paper towels for this process, as they can scratch the bolt.

7. Now, for the lubing. Take your lube of choice (I personally use slick honey), and put a thin layer on the beercan o-rings, and the front wall o-rings (both the inside and outside o-rings). With these cleaned and lubed, you can put them back in the gun. Front wall, then the beer can (with the longer side on the beercan facing forwards).

8. Now, put your grease on the o-rings of the bolt itself, and a layer on the entire bolt itself (except for the really skinny part of the stem). Make sure you put a fair amount on the stem o-rings, which are located on the very rear of the bolt.

9. Put thin layers on all three o-rings located on the top hat. Too much grease on the inside o-rings here can gunk up the travel of the bolt and shoot it down your barrel. Put the top hat back on your bolt once it is properly lubed, and put the sleeve over the top hat, and put the spacer right behind the sleeve, with the indentation facing forwards.

10. Lightly lube the o-ring of the back wall, and put it back on your bolt assembly, with the indetation facing ******ds.

11. Lube the o-ring on the back plug (again, lightly), and insert the back plug over the end of the stem where the two o-rings are.

12. Holding onto the backplug, carefully reinsert the bolt assembly into your matrix. Once it is all the way in, screw the back plug all the way in, and back it out 1/4 turn or until it is flush with the body.

13. Hold up! There's still an o-ring that needs to go back onto the front of the bolt. Put it back on, and put a light coat of grease on it.

Congrats. Your bolt it lubed. Once it is fully assembled, grip the front of the bolt and work it back and forth a couple times to get the lube settled in.

Also, another handy tip. When lubing, you usually need to put just enough on the get the part of the bolt shiny. Too much lube may equal to consistency and accuracy problems.

There you go. If anyone would be so kind as to show how to lube a DM4 bolt kit, that would be great.
__________________
R.I.P. Hunter S. Thompson

Trader feedback
Blue Baller is offline   Reply With Quote
 



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -8. The time now is 05:31 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.

Help / FAQ  |  Contact Us  |  About Us  |  Advertising Info  |  Link to Us  |  Privacy Policy  |  Terms of Use
Top

Paintball Review

Copyright © 2000-2007 Hillclimb Media