Proto Matrix Rail- Questions Answered! - Page 5

PBfire1 · 04-15-2007, 06:32 AM

It sounds a bit like what happened to me last weekend. I had to mess with my hyper 2 reg for about an hour to get it right. Make sure you set it and fire about 10 shots before adjusting the hyper 2 again. Raise and lower SLOWLY.

StumpyManager · 04-17-2007, 08:32 PM

so i was trying to take apart my hyper 2 last weekend, but when i put both allen keys in where they needed to be, only one of them came loose, and like, it was like that for 30 minutes and then i gave up

i tried to conctact DYE, and the vid of dissasembly of one on Youtube, but it just never came loose. Is there an easier way?

lucifer_sam · 04-22-2007, 05:10 PM

I recently bought a PMR and I've been on the warpath trying to upgrade everything under the sun. I managed to get everything including a DraXxuS Pulse, but I really wanted to get the RF module.

As of now, it seems that the trigger frame is slightly cramped. Will the RF module for the Pulse fit inside the stock trigger frame?

protofreak · 04-22-2007, 05:24 PM

it will but it wiil be tight
since you have been in a mad dash to up everything a newdesignz pro-light frame they have made extra room in it just for the rf module

bigwood212 · 04-23-2007, 04:48 AM

how is it tight? Just tuck the chip above the board in the back of the frame. There is pleanty of room in there. And it wont even be falling out or anything when you open the grip.

I did the same thing with my regular frame and my ul frame.

darktrooper5 · 04-24-2007, 08:25 PM

I've tweaked this thread a bit, added some questions,answers and some information here and there.

ilikepaintball7 · 04-27-2007, 08:41 AM

whats the pmr's highest bps capibility and in what mode.

chitownballa19 · 04-29-2007, 05:48 PM

the stock board is capped at 30 bps, and you can shoot it in whatever mode you want.

protofreak · 04-30-2007, 11:56 AM

Quote:

Originally Posted by ilikepaintball7

whats the pmr's highest bps capibility and in what mode.

28-30 but the modes youll have to use to get that high are the nxl and psp

pb_freak_57 · 05-01-2007, 04:35 PM

im kinda new to the rail and read the manual and still kinda dont understand what dwell is. can any please explain it and how it works?

darktrooper5 · 05-01-2007, 05:06 PM

Dwell is how long your bolt stays forward. It controls your bolts travel time basically. Lowering your dwell gets you lower velocity, shootdown, but higher gas efficency in some cases. A really high dwell, increases velocity, can slow your marker down and sucks up more air.

A balance is key. Your stock dwell is 25, break you marker in for a few weeks/months before you touch your dwell.

pb_freak_57 · 05-02-2007, 06:00 AM

okay thnks

wrath_ltd · 05-02-2007, 06:32 AM

has anyones batterie harness come off the board and also the feedneck on mine was brittle...

darktrooper5 · 05-02-2007, 10:31 AM

Those guys like to break, you have got to be careful when dealing with them
A PM5/6/Dm4/5/C Harness will work.

lucifer_sam · 05-04-2007, 06:33 PM

My Rail recently started leaking gas from the barrel as I put it on. I took the bolt/manifold out, checked for torn o-rings and re-lubed everything, and it was still going. I don't think anything could have happened to the noid or the valve, so I'm guessing it might be some misalignment of the manifold. Anything I can do to check?

protofreak · 05-05-2007, 05:24 AM

make sure your little guide screw are in and in the right place and that your bolt can is screwed all the way into your manifold

sdwella · 05-10-2007, 03:07 AM

what type of grip replacement will fit the stock trigger frame????

ilikepaintball7 · 05-10-2007, 12:28 PM

i have 2 questions. does the pmr run on lp tanks or hp tanks?
number 2. when screwin in my tank, do i need to adjust anything before i put it in or just screw it in. i dont wanna mess anything up but im guessing just screw it in.

Mephisto21 · 05-10-2007, 09:55 PM

quick question and sorry if this is on another thread. how hard is it to put the dye UL Frame on. i know it is kind of a newbie question, but i don't want to mess up my gun.

protofreak · 05-11-2007, 03:20 AM

Quote:

Originally Posted by ilikepaintball7

i have 2 questions. does the pmr run on lp tanks or hp tanks?
number 2. when screwin in my tank, do i need to adjust anything before i put it in or just screw it in. i dont wanna mess anything up but im guessing just screw it in.

it will run on either but hp is better
and for if you have to ajust anything the rail is set to go out of the box

Quote:

Originally Posted by Mephisto21

quick question and sorry if this is on another thread. how hard is it to put the dye UL Frame on. i know it is kind of a newbie question, but i don't want to mess up my gun.

its as simple as taking the old one off unhook the eyes and noid then re hook them up to the ul board and put the new frame on