Need Rebel Help? Look no further! - Page 5

BlinkBaller · 02-15-2002, 05:16 PM

Anyone get co2 snow coming out of your Rebel BL above 50 degrees?

-RuShPB227- · 02-15-2002, 07:40 PM

when does it happen? right after a fresh fill?

-RuShPB227- · 02-15-2002, 07:41 PM

Thanks to KK, sid, or andrew, or whoever stickied this thread! *clap*

BlinkBaller · 02-15-2002, 08:17 PM

Whenever i shot, but it was in like the high 30s low 40s.

-RuShPB227- · 02-16-2002, 06:20 AM

in those temperatures, the c02 wont have time to expand, so it wiill look like snow.

BlinkBaller · 02-16-2002, 07:22 AM

Thanks

-RuShPB227- · 02-16-2002, 08:06 PM

thats what im here for.......

E coli · 02-18-2002, 03:58 PM

I have two rebels less than 3 mos old. Oldest (xmas) has had less than 1000 rds thru it. It does that Pbbbbbbbbbbbbbb full auto fail to recock thing after the first few rounds go thru it. When I check it in the garage before I play, it does better but still not as it should. New, both performed flawlessly, and I fear the young un will develop the same problem. (I got it for a spare) I called 32 deg and TJ says if the sear is broken they would replace, but not if it had "normal wear". Both sears are slightly worn at the rear. Before I spend $ on parts or repairs, what are the suggestions? Send specific questions, I'll try to send specific answers.

-RuShPB227- · 02-18-2002, 04:05 PM

oil your bolt. I used to have the same problem with my rebel when I had it, stupid me took the orings off the bolt and then it worked fine, but i wouldnt do that.

E coli · 02-18-2002, 04:28 PM

I'll try it! If it works, I'll be forever in your debt. Let you know if so.

E coli · 02-19-2002, 02:08 PM

Didn't work, more of the same. Try again? I'm sending it back, let them figure it out!

Squidboy · 02-19-2002, 03:27 PM

Just got my rebel VTL today. I need to know how to strip it so that I can clean it and oil it.

E coli · 02-20-2002, 06:53 PM

NPS/32 deg is sending me an '02 rebel to replace my sick '01! Congrats to me! Hope y'all have the same good fortune.

-RuShPB227- · 02-22-2002, 04:57 PM

Squid, to take it all apart, all you have to do is take out the field strip pin. Once you do this, the bolt and spring should come out. From the bottom part, you can tilt the gun back and get the hammer. Basically thats all on the gun except the sear, which all you have to do is take off the trigger frame.

Squidboy · 02-23-2002, 03:45 AM

I CANT GET THE STRIP PIN OUT!!!! The little ball on the end won't let me!

Bad007 · 02-23-2002, 09:08 PM

try pushing down on the velocity adjuster and it will relieve some of the tenion then while doing that yank it out. I do not reccomend this but....hammers work.

Squidboy · 02-24-2002, 10:03 AM

I am really disappointed in my two rebels. I just used them for the first time yesterday. They would either give two shots and not recock, or they would give one shot and never recock. I am taking them apart today to see wht the problem is, and I will post again later.

takeastand · 02-26-2002, 07:58 PM

I have a rebel vertical and I was wonderin if i got the Bob Long Cyclone bolt ( a rear cocking bolt), do i still have to buy the factory upgrade to rear cocking or can i just get the B.L. bolt and the connecting pin to make it work?
thanks

-RuShPB227- · 03-06-2002, 02:23 PM

Quote:

Originally posted by Squidboy
I CANT GET THE STRIP PIN OUT!!!! The little ball on the end won't let me!

push from the other side........

Squidboy · 03-07-2002, 02:15 AM

I got the thing apart finally, I had to push on the velocity adjuster really hard and then push it out, thanks for you guys' help