Need Rebel Help? Look no further! - Page 7

ceniack · 04-24-2002, 02:45 PM

double feeding even with new ball detent, shooting diablo inferno paint. ACI one peice zero gravity barrel, bob lond delrin bolt (all the parts that could be causeing the problem) any suggestions?

teamfortman · 04-24-2002, 07:16 PM

32degrees told me they would repair my rebel le but i do not know where to ship it too.....

Bad007 · 05-01-2002, 03:14 PM

Lol, tic tacs has the same rank in opinion as anyone here and it's not what he thinks but what you think. And also the rebel Xtreme has the SAME upgrades as as Spyder Shutter. get an Xtra

i like tictacs · 05-01-2002, 04:02 PM

why? Vertical feed SUCKS on any blow back. it actually feeds SLOWER then powerfeed. Why? blowback, goes straight up and literally pushes the balls back up. with powerfeed there is a blowback vent, so it isnt as bad.

Bad007 · 05-01-2002, 08:58 PM

I agree but they were suggesting that, and I doubt you will notice it if you have a revy and I used one and they work fine and I like them better. And then why is vertical feed on so many guns? On many blowbacks there are vertical feed such as timmies.

Bad007 · 05-12-2002, 11:05 AM

32 degrees....look on their site and there will be a page where it will help you out.

somedude12345 · 05-14-2002, 03:01 PM

what is the best brand of paint to use for a rebel? My gun is a rebel 02 vertical. I will someday get a terminator barrel for it too.

Bad007 · 05-14-2002, 09:10 PM

depends, what kind you can get and the bore size of the barrel your using. And if you want to pay for like tourney or paint or practice paint. try to match the bore of the barrel, a nice fit would be the best, want it to slide through but still kinda snug.

somedude12345 · 05-15-2002, 01:21 PM

alrighty, my barrel is 68 cal. so I should get 68 cal. paintballs. But, what brand is the best? I just play with my friends, nothing serious. just fun, casual paintball. I was thinking 32* or diablo or pmi or something. thanks

i like tictacs · 05-15-2002, 01:52 PM

proball for rebels, they shoot excellent, and the arnt thin-shelled so your less likely to break

Fastlearner · 05-20-2002, 12:03 PM

Chopping / doubling balls with a '02 Rebel VTL or Bottomline? Try these steps:

1) Turn your powerfeed to the off position.
2) Clear the breech of paint balls.
3) Fill the power feed with the paint you want to use.
4) SLOWLY! Turn the power feed knob COUNTERCLOCKWISE!!! until the balls start to feed easily but not wide open.
5) Rapid fire the gun.
6) Repeat steps 4 & 5 until reliable feeding without chopping / doubling occurs.

long winded explanation why this works.... email me if you want it

DeFiant · 05-20-2002, 04:59 PM

My freind is haing trouble with his Rebel Extreme. it leaks gas down the barrel and i know this is usually caused by a bad cup seal but 32 degrees are different. Does he have to buy a new cup seal thing or is there something i missed?

Snatch · 05-31-2002, 04:28 PM

I was going to buy a Rebel vertical, is it worth the money or should I upgrade to an LE or Xtreme?

Dark Cloud · 05-31-2002, 05:53 PM

Buy a VTL or an Xtreme. Dont get the LE no matter what you do okay

hybrid79 · 06-08-2002, 04:06 PM

I have a brand new rebel xtreme and it is double feeding on me alot. every 10 or so balls i will get 2-5 balls out of the barrel at on time. Any suggestions to help me out?

MNsniper · 06-11-2002, 08:17 PM

i have a rebel btmline, with all the little gizmos on it, but i can't get it to recock. when i pull the trigger, the bolt goes forward and shots but the hammer just won't go back. it hits the valve pin and just stops. anyone got any ideas?

Bad007 · 06-23-2002, 10:20 AM

defiant-have you check all the o rings and have you oiled it?

mnsniper-the bolt and hammer are connected so I doubt one is just going to do its own thing. are you just trying to say your gun won't recock? Kinda sounds like the spring, my want to try a couple springs out. or your sear may be bad. youll have to explain it a little more.

MNsniper · 06-24-2002, 05:46 AM

i've changed all the springs in it and it still won't recock. and i've taken every part out cleaned it oiled what need to be oild and put everything back together. the sear is brand new so it's not that. and the hammer doesn't even come back it just stops when it gets to the valve.

sorry i just had to put this smily in cause it amuses me so much

Bad007 · 06-26-2002, 08:04 PM

i hope you have the same "paintball" fettish that i have
love you .... bye

32degreesking · 07-09-2002, 11:45 AM

Anyway i got a rebel vtl and got a 32 degrees expansion chamber and quiet riot barrrel but for some reason it broke after i got the ex the guy at the store put the c02 in and you could hear leaking from in side the barrel the guy tried everything but couldnt find where it was coming from. he then checked the co2 and that wasent leaking either he then just slowely heard it go away but if it happends again what should i do also when i put the co2 in and i cock it and I shoot it it won't recock but it doesnt sputter so i know therre is still co2 left