pbReview.com - Paintball Reviews and Paintball Fields

  Join pbReview.com  |  Log In  
pbReview.com - Paintball Reviews and Paintball Fields

Search:

  
Home     |     Paintball Articles     |     Paintball Videos     |     Paintball Gear     |     Paintball Fields     |     Paintball Stores     |     Hot Deals     |     Paintball Forums     |     Chat
Go Back   Paintball Forums > Specific Marker Forums > Evil Paintball


Reply
 
Thread Tools Display Modes
Old 09-08-2003, 04:22 PM   #1
Spartan 2
EviL Ambassador
 
Spartan 2's Avatar
 
Join Date: Nov 2002
Location: Kingsville, MD (near Baltimore)
Send a message via AIM to Spartan 2
The Official Evil Omen FAQ

I figured these are those most asked questions right now. There are lots of little things but they are not asked as often. When a question becomes asked more, I will add it.


The EviL Omen FAQ


Q: How do I adjust my new evil omen?

A: It should come ready to fire; you most likely will have to adjust the re-cock and velocity before you play. It should come from the factory already adjusted, but mine was not, and if the re-cock is set to high, your going to loose a bumper.

When you get your omen, here what I suggest you do:

Do not adjust the regulator, tighten it down were it is, and leave it. Read all of the instructions and locate the re-cock adjustment, look on the parts sheet and look for the re-cock screw that will give you the general location. IT IS NOT THE COCKING ROD...thatís what I first thought. It should be in the middle of the body, outside of were the valve is.
Gas your gun up, and turn the re-cock screw clockwise to tighten it up. Cock the gun and fire; it should NOT re-cock on its own. Keep backing the re-cock screw out till it can re-cock on its own and keep up with rapid fire. Go a little higher then you want after that, but no more then a quarter of a turn. This is called sweet spotting the re-cock pressure. You will have to do it every time you adjust the regulator. But if you want to be fast, just lower the re-cock every time you raise the regís pressure, and visa versa.
The regulators pressure output should be fine, but most-likly it will have to be adjusted. Adjust the re-cock all the way down again and turn the regís pressure up for more velocity and down for vise versa. Do single shots with the re-cock off to adjust the velocity, Every time you adjust the reg, shoot the gun 2 times to get the regs new set pressure. When you chronograph it with no re-cock, you want it to be 10 fps faster, because when you engage the re-cock it will bring the velocity down 10 fps.
I suggest using HPA when adjusting the gun....my got all frosty when making the gun "keep up" while adjusting the re-cock. At least use a remote or ant-siphon if you have one.


Q: How do I adjust the regulators pressure?

A: There is a ring located on the middle of the Regulator. This ring is held by a friction screw, to adjust the reg loosen the screw. Instead of bothering with the closewise method that always got people confused as to how to look and the gun and turn it which way.
While you are looking at your gun from the side that the recock screw is located, turn the ring left to decrease pressure, and turn the Ring Right to raise the pressureTighten the screw when itís adjusted properly. Simply remember lefty-Lower, righty-Raise


Q: How does the CAM feed work?

A:
Think of it more as a two-stage seesaw with reeds.
The two reeds, which are spring loaded, sit to the right of the ball waiting to push it into the breech, but the bolt is closed holding a ball in the barrel.
When you pull the trigger, the inside striker goes forward, shoots the ball and starts the re-cock.
When the inner/outer striker comes back, it brings the bolt with it.
On the right side of the bolt are cutaways.
The first groove or cutaway on in the back has the reeds in the full right position.
As the bolt comes back, the cutaway in the bolt is less and the reeds start to move the waiting ball towards the breech.
As the bolt uncovers the feed, the cutaway in the bolt disappears and the reeds move fully to the left and push the ball into the breech.
The reed on the outside is a little wider and does not go fully into the side of the body and acts as a ball stop to keep another ball from falling into the ready position.
As the bolt goes forward, it pushes the ball into the barrel and the reeds go back to the far right and allow another ball to fall into place waiting for it's turn to chamberÖ


Q:Why is my gun not re-cocking, even with the recock adjust al the way out?

A:
This can be cause by a couple of miss adjustments.
First check your Strikers bumper, if it is broke, teres the problem, this is cause by having the recock to high. If it's is not broken it is probally cause by over pressurizing the gun. When there is to much pressure behind the valve, the Omens striker is not able to open he cup seal enough to shoot or re-cock the gun. The regulators output must be with in a curtan range to work properly. Turn your regulator all the way down, and adjust your recock all the way in. Start from stratch and slowing bring your regulators pressure up till you velocity is 10 fps faster then you want it. Then start the re-cock sweet-spotting prosses.


Q:

(If you think of some more, please add them)
__________________
EviL-

RULE THE WORLD

Don't run, you will only die tired.

Oh come Hither my Evil friends. Let us dance upon our MINION of pure EviL, on the sup air ball field. Let us give thanks to this EviL OMEN that the Lord HEATHEN has sent to us. Let us be faithfull till Judgement day, when EviL shall finally RULE THE WORLD.

Last edited by Spartan 2 : 09-09-2003 at 11:29 AM.
Spartan 2 is offline   Reply With Quote
Old 09-09-2003, 10:30 AM   #2
radishboy
trisomy 21
 
radishboy's Avatar
 
Join Date: Apr 2002
Location: chesterfield, MI
Send a message via AIM to radishboy
the evil omen
www.evil-paintball.com

price range: $300-$375 for an older model
$450-$550 for a newer model
$600-650 for a splash
-----places to buy:
www.e-paintballoutlet.com
www.actionvillage.com
www.ratgunz.com
www.xpaintball.com

specs

last update: 5-9-04

feed system: cam operated force feed
-----as the back block moves backwards, a lever pushes the ball into the breech, while another lever prevents the other balls from going behind the main cam feed arm.


action
semi-automatic, true closed bolt cycle, pneumatic re-cock, electro-mechanical firing control (sear tripper), independent hammer and re-cock piston, external re-cock regulation.

length: 19.7 inches
height: 8 inches
weight: 2lbs, 7 oz.
power source: co2, regulated n2 and regulated HPA
operating pressure: 200-500 psi (recommended)
marker pressure:do not exceed 500 p.s.i.
input reg pressure do not exceed 1000 p.s.i

features

trigger
two way adjustable double trigger
-----shortest 100% effective pull: about 1 - 0.5mm
efficiency
about 1200 shots from a 68/3000 HPA tank
barrel
-----cocker threads
-----12" stock barrel length
power source input
bottom line on/off assembly
feed neck threads
same as impulse, bushmaster, 2k3 fish


(more) frequently asked little questions

Q: am i supposed to have a ball detent?
A: no. double feeding isn't that big of a problem due to the fact that its closed bolt, BUT the ball rolling out of the barrel is. avoid using really small paint, and you wont have a problem

Q: are there currently any aftermarket parts for the omen?
yes, see the list below. it will be updated as more products are released

boards and chips
morlock board: requires modifications.
PDP chip (up to 25 bps with adjustable debounce)

----www.pdpaintball.com
frames
currently none
bolts
rj skateworkswas supposedly coming out with a new delrin bolt for the omen, but i don't know how thats coming along.
----www.rjskateworks.com
valves
none.
hammers
you can get a new back block and hammer assembly from evil, but all newer models come stock.
----www.evil-paintball.com
feed necks
ND lowrise
evil smokestack
twister lowrise
any feed neck that fits impulses or bushmasters

barrels
any barrels that fit the autococker.
grips
none
drops
the omen has standard bottomline fittings
ASA's
evil ASA with gauge
----www.evil-paintball.com


Q: my velocity is low:
A: increase the reg pressure, but not over 600 psi, which could aslo decreas FPS
Q:marker does not recock every shot
A: gas supply is low
Q:marker does not recock during skips:
A: hammer o ring needs lube, or recock pressure is too low.
Q:marker skips often
A: cam push arm is rubbing on marker frame, or your outshooting your hopper.
Q:paintballs break in the barrel
A: barrel is too large for your paint.
Q:velocity is very erratic
A:barrel is too large for paint, poppet o-rings may need to be lubed.
Q:bolt or cam arm breaks paint
A: marker recock too hard, reduce recock pressure. bumper may be damaged, hammer coushion may be worn out or damaged.
Q:bolt james between cam arm and anti doubler arm
A:force fed loader is pushing too hard, debris between push arm and anti doubler arm, anti doubler arm is jamed or rubbing on marker frame, push arm or anti doubler arm is damaged.
Q:marker does not fire with eatch trigger pull:
battery is low, marker is not assembled correctly, hammer plate is lose, rear frame screw is missing.
Q: barrel leak
A: pressure too low to seal valve, debris stuck in valve is holding it open
Q: my gun leaks when i gas it up.
cock the gun before you connect the air source.

tell me if i missed anything
__________________
paint to barrel match can match my foot to its face.

Last edited by radishboy : 05-09-2004 at 03:38 PM.
radishboy is offline   Reply With Quote
Old 09-10-2003, 04:17 PM   #3
Mcot2
Evil Maniac
 
Join Date: Jun 2002
Location: Pine tree state
Send a message via AIM to Mcot2
Lightbulb

Ill post a few.

Q: What is evil's tech support number?

There number is 1800 579 1633 Mon-Thursday 9-5 central time.

What is the Warentee on the omen?

The warentee is one year, out of warennete support may cost an additional $20 plus parts.

What should I use to oil/greese my omen?

Regular paintball oil on the hammer assembly, or a light coating of lithum greese, dow 55, or dow 33(Shocker lube) Do not oil the bolt.

How often should I greese my omen?

Greese/oil the omen after every 2 cases, also check the bumper and springs for wear and replace as nessisary.

Are there any furture upgrades for the omen?

Yes, evil plans to release a lo rise, a blade trigger, new grips, a new bumper design, and a new asa with a guadge port, some of which will debut at world cup 2003, and some will come later (by december).
__________________
E-cocker with nexxus + slik + mac dev + ccm + hybrid parts.

and

Ebladed Turtle Cocker

Last edited by Mcot2 : 09-10-2003 at 04:23 PM.
Mcot2 is offline   Reply With Quote
Old 09-21-2003, 08:46 AM   #4
Spartan 2
EviL Ambassador
 
Spartan 2's Avatar
 
Join Date: Nov 2002
Location: Kingsville, MD (near Baltimore)
Send a message via AIM to Spartan 2
Q:
What are some of the New Products that Evil is planning to release at world cup and latter on?

A:

-Driver barrel : Features, 1 piece construction Step bore for 2 piece function. 30degree porting, MSRP of $99

-Low Rise: can be used on Omens and other Bushy/IMP threaded bodies.

-Scion: Rail mounted HPA system... destroys all competition when it comes to regulation, push button on/off, MSRP of $450

-Tapped Omen ASA for a guage.

-Evil Lube.



Evil Guns to be released:

-Pimp
-Minion
-Heathen
-Avatar (The best of the best)


(last updated 9/20/03)
__________________
EviL-

RULE THE WORLD

Don't run, you will only die tired.

Oh come Hither my Evil friends. Let us dance upon our MINION of pure EviL, on the sup air ball field. Let us give thanks to this EviL OMEN that the Lord HEATHEN has sent to us. Let us be faithfull till Judgement day, when EviL shall finally RULE THE WORLD.
Spartan 2 is offline   Reply With Quote
Old 10-30-2003, 01:40 PM   #5
radishboy
trisomy 21
 
radishboy's Avatar
 
Join Date: Apr 2002
Location: chesterfield, MI
Send a message via AIM to radishboy
oh crap. major typo there. good eye.
__________________
paint to barrel match can match my foot to its face.
radishboy is offline   Reply With Quote
Old 11-10-2003, 01:44 PM   #6
ZackWoody123
 
Join Date: Nov 2003
when does all of the new evil guns come out?
ZackWoody123 is offline   Reply With Quote
Old 11-16-2003, 09:40 PM   #7
jaack
 
Join Date: Nov 2003
Send a message via AIM to jaack
where is the new board available? what mods does it require?
__________________
"what you think just 'cuz a guy reads comics he can't start some ?"
jaack is offline   Reply With Quote
Old 11-17-2003, 12:48 PM   #8
Spartan 2
EviL Ambassador
 
Spartan 2's Avatar
 
Join Date: Nov 2002
Location: Kingsville, MD (near Baltimore)
Send a message via AIM to Spartan 2
Guys please, this is a FAQ not a place to ask your own questions. Thats what the fourm is for. Ask them there.


And to the Guy under me, Why did you post here? I do not car if you could not find it. Post a new thread asking the question then. But I know their has been a thread on that topic, so a search in this fourm.
__________________
EviL-

RULE THE WORLD

Don't run, you will only die tired.

Oh come Hither my Evil friends. Let us dance upon our MINION of pure EviL, on the sup air ball field. Let us give thanks to this EviL OMEN that the Lord HEATHEN has sent to us. Let us be faithfull till Judgement day, when EviL shall finally RULE THE WORLD.

Last edited by Spartan 2 : 11-20-2003 at 03:48 AM.
Spartan 2 is offline   Reply With Quote
Old 11-19-2003, 06:31 PM   #9
Dziuban
 
Join Date: Oct 2003
Adjusting Trigger?

Hey there, i was just wondering how do u adjust the trigger pull on the OMEN... sorry if it is posted but i could not find it and i just got the OMEN today for my birthday... help me if u can
Dziuban is offline   Reply With Quote
Old 02-27-2004, 12:53 PM   #10
penguins_r_kewl
Shlumpeet
 
penguins_r_kewl's Avatar
 
Join Date: May 2003
Location: Equator
Do Omens have any kick?
__________________
waaart
penguins_r_kewl is offline   Reply With Quote
Old 02-27-2004, 07:41 PM   #11
radishboy
trisomy 21
 
radishboy's Avatar
 
Join Date: Apr 2002
Location: chesterfield, MI
Send a message via AIM to radishboy
a tad, depending on how well your recock pressure is adjusted.
__________________
paint to barrel match can match my foot to its face.
radishboy is offline   Reply With Quote
Old 05-10-2004, 08:17 PM   #12
PB-Predater
Meet my little friend.
 
PB-Predater's Avatar
 
Join Date: Apr 2004
Location: not sure =/
Send a message via AIM to PB-Predater
You guys may have allready posted it but I didnt see it so could you tell me how many BPS it does?
PB-Predater is offline   Reply With Quote
Old 05-11-2004, 04:40 AM   #13
radishboy
trisomy 21
 
radishboy's Avatar
 
Join Date: Apr 2002
Location: chesterfield, MI
Send a message via AIM to radishboy
15 bps stock. i honestly dont think i put that on there...
__________________
paint to barrel match can match my foot to its face.
radishboy is offline   Reply With Quote
Old 05-28-2004, 08:54 AM   #14
freehand
 
freehand's Avatar
 
Join Date: May 2004
Omen Model

Hey i noticed you said that there are several different types of omens, i knew there was the ones with the funky colors and a black one, how do i know if i have a new model or a classic omen? i ordered one off ebay the other day...
freehand is offline   Reply With Quote
Old 05-28-2004, 10:50 AM   #15
radishboy
trisomy 21
 
radishboy's Avatar
 
Join Date: Apr 2002
Location: chesterfield, MI
Send a message via AIM to radishboy
old ones have a smaller trigger gaurd and silver trigger, newer ones have a larger gaurd and silver trigger, and the newest ones have a larger gaurd, a black magnesium trigger, and a charge port cover. theres more but that's the easiest way to tell.
__________________
paint to barrel match can match my foot to its face.
radishboy is offline   Reply With Quote
Old 05-28-2004, 11:29 AM   #16
freehand
 
freehand's Avatar
 
Join Date: May 2004
i'm guessing i have one of the two older ones, is it worth keeping?
what is the difference besides looks?
freehand is offline   Reply With Quote
Old 07-14-2004, 07:57 AM   #17
Redneck724
The Paintball Playa
 
Redneck724's Avatar
 
Join Date: Apr 2004
Location: Fairhope,AL
Send a message via AIM to Redneck724
What is the bumper on the omen?

What is the bumper? what does it do? where is it on the gun? how much does one cost to replace? does it break easy?
Redneck724 is offline   Reply With Quote
Old 08-08-2004, 11:53 AM   #18
knuckhead09
Herbal Orgasms
 
knuckhead09's Avatar
 
Join Date: Nov 2003
Location: SoMich
Send a message via AIM to knuckhead09
Its the bumper behind the hammer. It will break if you have the recock set too high.
__________________
knuckhead09 is offline   Reply With Quote
Old 08-10-2004, 08:24 AM   #19
UnderEstimated
 
Join Date: Aug 2004
Location: Wisconsin
Where can i get an older model of an Omen?

So, where would i get an older model of an Evil Omen? And if i do get one, what is different about the older ones than the newer ones? Are there more defects on the older models?
UnderEstimated is offline   Reply With Quote
Old 08-10-2004, 02:00 PM   #20
Redneck724
The Paintball Playa
 
Redneck724's Avatar
 
Join Date: Apr 2004
Location: Fairhope,AL
Send a message via AIM to Redneck724
goo

goo
Redneck724 is offline   Reply With Quote
Reply



Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -8. The time now is 11:49 PM.


Powered by vBulletin® Version 3.6.4
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.

Help / FAQ  |  Contact Us  |  About Us  |  Advertising Info  |  Link to Us  |  Privacy Policy  |  Terms of Use
Top

Paintball Review

Copyright © 2000-2007 Hillclimb Media