Settings thread - Page 2

4THDEGREE · 03-28-2005, 07:14 AM

I could get to 17 in simulate. I have since replaced it with the Tadao board. But while I had the Frenzy in, it was wicked fast!

infuse05 · 03-28-2005, 01:57 PM

arent u limited to 12 bps???

4THDEGREE · 03-28-2005, 03:54 PM

I find that it varies from board to board a bit. YOu do have to keep in mind that these readings are still measuring peak bursts and not averages of a set time.

C-Unit10 · 04-09-2005, 11:17 AM

Texas Storm Timmy
Frenzy 113
Dwell: 8.0
Eye: Forced
BIP: 0.0ms
Bolt Delay: 15ms
Timer: 5:00
Debounce: 2.0
MBounce: 0.0

i switch my debounce and mbounce depending on where im playing...if im playing with pople who are ramping those are my settings...if im playing with honest players no ramp or anything i do debounce 10 and mbounce 2 usually

4THDEGREE · 04-09-2005, 05:12 PM

C-unit, if you up your BIP just a bit, it should prevent chops just a bit better, like 0.2.

dantriggerhappy · 04-09-2005, 05:44 PM

Terry reccomends keeping the 0.5 BIP from the factory, he says he leaves all the guns he techs like that, except for a rare few that are PERFECT timmies.

C-Unit10 · 04-10-2005, 06:15 PM

alright...thanks so much guys!

4THDEGREE · 05-09-2005, 12:15 PM

I have to go back and do a little research on this. I thought for sure I had read that the BIP really doesn't have a lot of bearing when using Halos and Reloader B's. On the other hand that bolt delay should not be below 15. I will get back to this tonight.

Ash2Alias · 05-14-2005, 05:43 PM

4th, I saw your first post about settings with the frenzy but was that with 113, 116, 127.1 or 127.4?

I have an alias and just got my frenzy flashed to 127.4T and was wondeing about the settings for that.

dantriggerhappy · 05-14-2005, 05:44 PM

settings will be no different than what they were previously.

dantriggerhappy · 05-14-2005, 05:48 PM

Too lazy to edit: Repost of my settings on my alias with 127, delrin pistons, and lpr and volumizer at 55 psi.

Dwell: 8 ms.
Eye Mode: Force
BIP: 0.5 ms.
Bolt: 08 ms.
Timer 10 minutes.
Delay 00
R BPS: 8.
Debounce: 25
Mbounce: 3

Dan

Ash2Alias · 05-14-2005, 05:56 PM

Thank you, I wasnt sure if it would make a difference with the flash.

4THDEGREE · 05-15-2005, 04:32 PM

Quote:

Originally posted by Ash2Alias
4th, I saw your first post about settings with the frenzy but was that with 113, 116, 127.1 or 127.4?

I have an alias and just got my frenzy flashed to 127.4T and was wondeing about the settings for that.

Since the frenzy board logic is similar thorughout the various models as far as settings go, my original settings will get you in the ballpark, whichever one you have. Fine tuning will happen depending on which ram, bolt, hopper combination you have.

looms · 06-10-2005, 09:40 AM

I have a new 05 Alias. I tinkered with the settings a bit before playing with it and when i used it in the tourny it was shooting fine. But when i ripped long streams it would chop. So basically im looking for some basic settings that are good for reliability and no chopping. Its ok if i have to sacrifice speed. So does anyone have any settings that fit my needs? By the way i have the new frenzy that comes stock in 05 models.

thanx

dantriggerhappy · 06-10-2005, 10:26 AM

I would up your delay one or two, and it almost sounds like your loader isn't feeding correctly/fast enough. If that does not help, re-adjust your ram and get a pair of extra super hard detents from www.paintballkingdom.com

Dan

PaintBaller1818 · 06-14-2005, 05:08 PM

I'm wondering if these settings apply roughly to all timmy's, because they have been pretty uniform. I have a 2k2 (gun in sig) and I want it to be as fast as possible without becoming ilegal (nppl rules). Any suggestions?

4THDEGREE · 06-15-2005, 12:01 PM

Quote:

Originally posted by PaintBaller1818
I'm wondering if these settings apply roughly to all timmy's, because they have been pretty uniform. I have a 2k2 (gun in sig) and I want it to be as fast as possible without becoming ilegal (nppl rules). Any suggestions?

\

Board - WAS 2.8

Dwell - 8
Debounce - 2
Eyes - Forced
BIP Delay - 0.1
Ram Delay - 15.0
Bolt Delay - 0.1

You will have to experiment a bit with the debounce depending on how you have your trigger set up, but these are excellent starting points.

PaintBaller1818 · 06-15-2005, 04:09 PM

^ Thanks I'll try them out and adjust from there.

PaintBaller1818 · 06-16-2005, 11:46 AM

Board - WAS 2.8

Dwell - 8
Debounce - 2
Eyes - Forced
BIP Delay - 0.1
Ram Delay - 15.0
Bolt Delay - 0.1

I have my settings at the ones above, and I seem to be chopping way more than I should (10 balls a hopper) Which setting should I change to make sure this doesn't happen?

I also am confused after I break a ball, is ther anyway to "clean" the eyes so that I don;t continue to chop paint due.
EDIT: sorry about the double post

boardbreaker05 · 06-18-2005, 01:38 PM