Settings thread - Page 3

4THDEGREE · 06-19-2005, 03:33 PM

Quote:

Originally posted by PaintBaller1818
Board - WAS 2.8

Dwell - 8
Debounce - 2
Eyes - Forced
BIP Delay - 0.1
Ram Delay - 15.0
Bolt Delay - 0.1

I have my settings at the ones above, and I seem to be chopping way more than I should (10 balls a hopper) Which setting should I change to make sure this doesn't happen?

I also am confused after I break a ball, is ther anyway to "clean" the eyes so that I don;t continue to chop paint due.
EDIT: sorry about the double post

Up your BIP delay a bit. Are you sure they are chops and not barrel breaks?

PaintBaller1818 · 06-20-2005, 09:20 AM

Pretty sure. there was paint ont he very front of the bolt and eyes.
I also am confused after I break a ball, is ther anyway to "clean" the eyes so that I don;t continue to chop paint due to the eyes being covered in paint?

I'll try the bip thing. thanks

dantriggerhappy · 06-20-2005, 09:26 AM

Take off the eye covers, then take out eyes, clean detents, eyes, and eye covers.

PaintBaller1818 · 06-20-2005, 10:27 AM

I mean in the middle of a game. I know it shouldn;t chop really at all but if it dodes (like with mine) is ther a way to "quick clean" them? Like would a swab work?

dantriggerhappy · 06-20-2005, 11:42 AM

It might help, but it wouldn't help very much since unlike the ball detents, the eyes are somewhat internal.

Catfish2850 · 06-21-2005, 01:53 PM

Can someone give me a starting point for Tadao in a Species? I had Frenzy 113 and could not get it to stop bouncing no matter how I adjusted the dbounce or mbounce.I have techna trigger and Halo B hopper.Will have Tadao installed tomm.Help if you guys could.Hope this board works better than the Frenzy 113.And thanks in advance.

speedy2k4 · 07-31-2005, 06:35 PM

alright lemme know if this sounds ok:
2k2 gz timmy w/ frenzy 113
75psi lpr pressure
dwell: 8.5ms
eye mode: forced
BIP delay: 0.3ms
bolt delay: 14ms
debounce: 8
Mbounce: 2

dantriggerhappy · 07-31-2005, 06:38 PM

you should be able to run the bip at .5.

cat- try rocking it at a debounce of 15, mbounce of 3.

speedy2k4 · 08-01-2005, 08:24 AM

alright so question, the bolt delay on frenzy, is it equal to like the bolt and ram delay on w.a.s.? if i should have my bolt delay for frenzy 113 at 15ms, what should i set the w.a.s. 2.8 to, 15 ram and .1 bolt?

dantriggerhappy · 08-01-2005, 08:33 AM

huwoiaw;ljdafs; what???????????

Since my alias is amazing, I run it at a BIP of .5, bolt at 08 ms, and a delay of 0. Most timmies have to have a bolt delay of about 15 or so ms, the lower the faster and more responsive (so my gun rips

). I do not know about WAS boards because I refuse to use them and I have never used one, you would be best asking either lopez, 4th, or jaster on that one.

4THDEGREE · 08-01-2005, 09:03 AM

Quote:

Originally posted by speedy2k4
alright so question, the bolt delay on frenzy, is it equal to like the bolt and ram delay on w.a.s.? if i should have my bolt delay for frenzy 113 at 15ms, what should i set the w.a.s. 2.8 to, 15 ram and .1 bolt?

Please refer to my very first post in this thread for my settings when running a WAS 2.8 board.

speedy2k4 · 08-01-2005, 09:15 AM

consider it referred to, thanks 4th

speedy2k4 · 08-16-2005, 03:29 AM

st bolt =

smartparts · 08-31-2005, 03:53 PM

Can any1 find settings for a frenzy 116.

4THDEGREE · 08-31-2005, 04:23 PM

Quote:

Originally posted by smartparts
Can any1 find settings for a frenzy 116.

Dwell - 8.0
BIP - .5
Bolt Delay - 12
DeBounce - 2
M Bounce - 0

These worked very well in both My Alias as well as my Ironman.

Tip Man*98* · 08-31-2005, 05:59 PM

Is the 116 worth getting flashed to a 127?

Tip Man*98* · 09-09-2005, 02:53 PM

Are these settings ok? I have not gassed up my marker yet because I do not have the correct bolt but that will come.

Frenzy 116

Dwell 7.0
BIP 0.5
Bolt 15
Debounce 3
Mbounce 0

These are the settings it came with. I got it off ebay..

PaintBaller1818 · 09-10-2005, 02:39 PM

I have a 2k2 timmy with a frenzy 127 board and i was wondering what the best settings are. Also if anyone has a site for a manual to this board it would be greatly appreciated. Thanks.

Dark Master · 09-10-2005, 02:52 PM

Quote:

Originally posted by Tip Man*98*
Are these settings ok? I have not gassed up my marker yet because I do not have the correct bolt but that will come.

Frenzy 116

Dwell 7.0
BIP 0.5
Bolt 15
Debounce 3
Mbounce 0

These are the settings it came with. I got it off ebay..

Raise the Dwell to 8.0 ms.

PaintBaller1818: Look at the setting Tip man posted and try those. Just make sure your raise the dwell to 8.0ms.

Mine:

Board: Infamous Tadao M3
Dwell: 10ms
Debounce: 20ms
Loader Delay: 2ms
AMB: 5
Bolt Delay: 15ms
Eye Mode: Forced
Mode: NPPL Semi Unlimited
Max ROF: 15bps (for semi limited, psp ramp, and nxl full auto)

Any things I should change on that?

PaintBaller1818 · 09-10-2005, 03:27 PM

Thank you Dark Master.