How to take a 'Cocker apart

[Uziel Gal]

Adjust the length of the 3-way actuation rod by unlocking the collar (small grub screw closes to the grip frame - no need to touch the other grub screw), and then turning it. In this instance, you will need to shorten the overall length of the rod.

[Sargent111]

it worked thank a lot

[sh(((o)))cker]

I just ordered my WGP Trilogy Competition Autococker off of actionvillage.com and I can't turn the velocity at all. The people at my local field didn't know what was wrong, can anyone tell me what they think can be wrong with it and how to fix it please.

[Dark Master]

That has nothing to do with taking a 'Cocker apart. But did you turn the IVG?

[Uziel Gal]

Or do you mean that you cannot turn the IVG? In that case, try loosening the screw that is holding the anti-tamper in place.

[7TANMAN7]

i have a promblem getting the gun to cock the timing hole thing i screwed it and i accidently cocked it and its stuck any ideas. thanks

[Uziel Gal]

Remove the grip frame screws and lower the frame a little. That will rlease the hammer from behind the sear (if I read your message correctly, your markers cocked but won't fire right?).

Once the hammer is back in it's at rest position, you can reverse the hammer lug adjustment you made.

[7TANMAN7]

now its working but the paintballs wont drop in because the bolt is in the way when its cocked what do i adjust to get the bolt out of the way? Thanks

[Uziel Gal]

You need to adjust the length of the cocking rod. Depending on what type of cocking rod you have, there is probably a small grub screw that locks the cocking rod knob to the rod itself. Loosen the grub screw, turn the knob anti-clockwise, and then tighten up the grub screw again. Keep repeating this adjustment a little at a time until the bolt just lines up with the back of the feed neck.

[gizmmo]

thanks really needed this and couldnt find it anywhere

[yotogi]

awsome thread! thanks for all of the hard work for us newbies out here.

[Accident]

how do you take the stock 04 prostock reg apart? i know its not externaly adjustable, but how do i change the pressure?

[Uziel Gal]

The stock reg is made in three parts, a central core in to which all the parts are installed, and an upper and lower end cap. Remove the lower end cap (the part that the hose is screwed in to) in order to expose the pressure adjuster.

Unscrew the pressure adjuster to access the reg seat seal, the piston neck o-ring and the spring and washer that hold the o-ring in place. Unscrew the top end cap to access the piston and spring washer stack.

[DarkStrike]

thanks, this helps me as a new user tremendously. ***** guide

[indianajones6]

what about totally removing a reg from a body? ive got it unscrewed but what i realized was that i had just unscrewed the reg from another part of it. it kind of looks like a small socket would pull it out? right? - Dan

[Georgeoffrey]

I think you mean removing the ASA from the body? The reg mounts to an Air Source Adapter, which yes, can probably be removed with a hex wrench.

[killertip212]

1/4inch 12point star socket
----or----
7mm hex socket

[Willie-mo]

this helps but i have a problem. i traded for a gun similar to this one yesterday and the guy said all you need to do is take the board out and tighten the screws to the asa mount (where the tank screws in?) and i did that but when i put the board back it does one of three things

a) the part where it gives you information goes completely red and will not operate any other way

b) same as above except for 1-6 red dots

c) it just wont come on at all

help? please?

[Uziel Gal]

Are the ASA screws coming in to contact with the board? If so, they could be shorting out the screen. The screws have to be short enough that they do not touch the board.

[Willie-mo]

the asa screws arent touching the board... i just put the board back and tried to turn the gun on and it wont do anything now it hasnt been doing anything cince last night