- - - - - - - - - - - - - - - - - - - Setup:
JT Excllerator 4.0
AKA Tornado Valve
Light Main Spring
Medium Valve Spring
20oz Anti-Syphon tank with Smart Parts on/off valve
Dark Horizons Titanium Striker
Lapco Vertical Adapter
Lapco Chrome Bottomline
Macroline Air Fittings/Hoses
Chrome Bob Long Torpedo Reg
Chrome Shocktech Drop Forward
- 12" all american barrel
- 12 volt revy
- pure energy 47 - 3000
- shock tech intimidator bolt (Don't reccomend doesn't fit perfectly some air comes back, it does fix the bolt jams which I had huge problems with)
- clamping feed neck
I had some more photos commemorating the final stages of this Excellerator 5.0's transformation - just figure I'd post them.
This is the pre-use final stage though: no macroline (still waiting for my Evil bottomline), Palmer's stabilizer requires calibration and I need to go to Home Depot to see if I can get some offset screws for my drop forward (no longer using inline screws as was present on the stock e-frame)
My hopper is off to the side. I just put on a RIP drive and Z-board, but plan to disassemble the whole shell to airbrush it maybe.
On that note, I'm not too sure if I'd want to airbrush my marker. It turns out the parts I've replaced seemed to have the right amounts of accents in the right places, so I'll leave the body the way it is...but maybe airbrush the bottom chamber (holding valve, striker bolt, spring, etc) black to match the 15* inward ASA block.
__________________ JT Excellerator5.0 - Zaibach Custom JT 14" Two-piece Barrel RMR Killstick Delrin Bolt Kingman ESP Frame w/ Rocking Trigger Trinity 15*(inward) ASA block Maddman Rocket LP Valve Palmer Stabillizer (w/ PHAT mini 700psi gauge) InYoFace Offset Sight Rail BSA RD30/22 SIL Red dot scope Halo Reloader B (w/ RIP drive & Z-board) Fireball Mountain Stiletto Drop Evil Bottomline ASA w/ on/off Pure Energy 20oz CO2 Tank (anti-siphoned) Busy w/ Custom Airbrushed Design
14" J&J Ceramic Barrel
BSA Red Dot Sight
Pure Energy Remote Line w/ Quick Detatch
Mil-Sim Air Through T-Stock
Mil-Sim Tac Light
Block Behind Trigger
We Are Woodsball
Join the Special Ops Brigade and enter this code when you sign up:67589 GetFree stuff like pods, nades and more.
Honestly, It's heavy as hell but it look's totally cool and matches any yellow jerseys you have. Unfortunetly I took it apart because I plan to sell the gun.
Other than what's stock, what ive added is the following:
-Jt one piece 14" barrel
-Trinity Spyder Front Block Assault w Gauge & LPC
-32 Degrees 6 Stage Expansion Chamber
-Extreme Rage 90º Swivel Elbow (edit: dont buy these, I had 2 and both broke a seal. I later just used the 90º part that came stock with the gun. It worked fine.)
Last edited by zdmechanic : 08-02-2006 at 09:01 PM.
A stock JT Excellerator 3.0 with an extra JT 14" one piece barrel. Only thing I added over the years (besides new o rings) Is a quick strip pin that I stole from a tac 5 tune up kit. It helps big time! I can fully field strip this thing in the middle of a match in under a minute... totally cool.
2005 Spyder Pilot ACS, red / black
32* 6 stage expansion chamber, red / chrome
32* drop forward, red
32* front block / LPC
Dye Sticky grips, red
WGP Triple Threat Barrel Kit
Shocktech shim kit / spring kit
Warrior Paintball clamping feedneck
-5.0 ball detent and cover (will fit, and wont crack like older one)
-Lapco vertical adaptor
-Jt 14" one piece barrel
-Trinity 6 stage exp. chamber
-Tac 5 quick strip pin (highly recommended for all 3.0 and 4.0 models.)
-wrapped parts in rubber tape
The parts that I have or am debating getting are the following:
-Delrin bolt (have, just not installed)
-horizontal scope mount
-Rocking trigger (It will work, however because the hammer is bigger, it needs to be shaved and cut to fit. Or, find a thin piece of rubber and cut it to fit between the gun frame and the trigger frame. Then you can use spyder compatible e-grips.)
Last edited by zdmechanic : 03-07-2007 at 03:23 PM.
Float like a butterfly Sting like a bee
Guns don't kill people i kill people.
Famous quotes made by Krashen
"look spider's they have baby's"
Main: RAP4 Storm, 20-inch trinity m-16 barrel, 12ounce co2, 200 round hop.
Leg Strap: PMI Traccer, 12 round tube, many more mods to come.