New replacement bolt for Black Draguns. Compatible wth all Black Draguns that use the Quick Snap Back bolt system. Not compatible with Black Dragun Compacts (coming soon). Made from Delrin, alot smoother than the stock aluminum bolt. Also will not scuff up the inside as bad. Rides on two o-rings around the air inlet, to prevent any air loss.
Open face design great for low pressure operation. Allows the air to flow freely, instead of impeding air flow like the stock venturi design. Installation requires transfer of stock bolt lug and set screw to new bolt.
The Check It Products Delrin Bolt is older, so while it may be available used and in a few cases new, it is not commonly available anymore.
Stock Bolt =P, compairable to Swan Creek N-Bolts, & Shocktech Delrin bolts.
Dragun E-1 - Stainless Steel Turbo Valve, Dye Xcel 14" Barrel, Check-It Products Dragun Full Force Delrin Bolt, Benchmark 4stg X-Chamber, Check-It Products High Volume Cell, Java High Pressure Coiled Remote, 20oz Pure Energy Co2 Tank, Fed by a VL eVLution hopper
Open face delrin design makes the bolt action of the Dragun more smoother with less recoil from less weight, increased air flow through bolt allowing for gun to hit higher FPS meaning you can run it at lower pressures allowing for better effeciency. Also the less weight of the bolt means less wasted air through blow back operation as there is less weight for the valve to work against when sending air to push the hammer back to catch onto the seer. Also seems to quiet down the noise a bit.
It is possible to strip part of the bolt since you must screw in some parts from your stock bolt, and since it is delrin it may be possible to strip so just be careful in installing it into your gun. Its not difficult to do though.
For an MSRP of $39.95 you get an open face delrin bolt made specifically for the Black Dragun markers excluding the compact series. This bolt is lighter, quieter, and more effecient then the stock bolt. Also seems to quicken the recock from blow back, so I'm not sure but it may even allow for a quicker cylic rate.. but then of course that would also depend on the frame. But this bolt is definately worth the price, seeing how most Delrin or Nylon bolts can run you up into the $50-$60 range... this one is reasonable. If you are an owner of a Black Dragun I highly recomend this bolt to you. I give it a 10.
Black Dragun, Psycho ballistic chamber, Dye ion dot sight, Thunder Pigs drop, 88ci Crossfire, All - American barrel, taso valve, check it trigger, ricochet
Cheap and keeps the bolt internal unlike using spyder bolts. Designed like any other open faced bolt but should be lighter due to not having any fat metal for a cocking rod. Stock cocking rod is just a screw which keeps weight down. Bandit bolt did its job but removed because it will hit you in the mask if playing tight. Never heard of lock tight being used on the gun because I was able to unscrew it by hand and sorry about it stripping your bolt but I used the teflon tape as directed.
Came out late and made me fork up 70+ dollars including shipping for a bandit bolt from swancreek. Bandit bolt also took two weeks to be made. re sold the bolt on ebay for 50 so its all good. Dragun owners should look into this bolt because you can't go wrong unless bandit makes it work internally.
Good upgrade to keep your black dragun working as an internal bolt gun. Makes spyder owners wish they didn't need a beaver tail. Baby your toyz and you won't see the negatives.
M3 Black Dragun Sniper LCD, Halo B (smoke), Dead X ex chamber, delrin bolt, teardrop 14"
It cycles quicker, a bit quieter, and the recoil is noticably less. Retains the flush cocking ability of the dragun (no bolts hitting your facemask). Is a bit (just a bit), easier on balls than stock bolt. Delrin surface eliminates lubing.
Doesn't seem to do much for accuracy, velocity or range. Seems like you can pull off a few more rounds per second than stock. You must blowtorch off the locktight from the stock bolt to remove the set screw and bolt and transfer it over to the new bolt. It is marketed towards helping a low pressure setup; however it doesn't change the fps very much at all. I was expecting to be shooting hot and I wasn't. Maybe a lighting bolt or bandit bolt may be better.
The bolt was relatively inexpensive so I am not going to knock it that much. It just didn't make much of a difference.
M3 Patriot Sniper, Check-It Delrin Full Force Bolt, Taso Turbo Valve, Lapco Delux Cup-seal, Angel Bullet Ball Detent (needs a spacer to fit right), R.A.M. air chamber, Check-It High Tension Spring, Stainless Steel four ball push pin, CCM angel high-rise feed clamp, angel feed port adaptor, Chrome Spyder flame drop w/Check-it uni-mount on/off ASA, Bob Long Torpedo Reg, Silver Check-It Sweet Spot Trigger (adjusted to the minimum, wil shoot if you flick the trigger frame!) HALO-B (a must if you want to shoot the 20bps it advertises), Full Freak barrel kit, Pure Energy 68ci 4.5k HP tank, steel braid line, Dye Rhino tank cover, sweat, and blood.
Accuracy, my marker is a lot more accurte with this bolt. MUCH easier on the internals. Love it, wise investment.
I've had no bad expierences with this bolt. But just the other day I got an Email describing an unheard of problem. The screw that connects the bolt to the Snap-Back ripped right out of the bolt! Imagin, this crew flying backwords towards whatever's in it's path... that's a projectile! I think that was just a one in a million chance though, I still love it.
Buy it, I really don't think you'll have that problem. If you do you can always sue someone. (ha. ha)
pi e-2 anti-siphon 20 oz co2, big daddy 12 in barrel, 12v w/xboard, steel braided hose, delrin bolt, and sweet spot trigger.
with regular bolt you shoot the same spot 5 times and 2 are where you want them and the other 3 are scattered, with this bolt you shoot further fast, and with less recoil and sound. I shot 5 times fast like i did with reg. bolt and all 5 were where i wanted them to go. this bolt kix ass and i love it.
the only bad thing is it is plastic and may have long term problems but you dont really need to worry about that.,
i think BD owners should buy this bolt "it is worth its weight in gold"