Shocktech Custom cocker I made
68 4500 center flag tank
Shocktech frontend kit ,shocktech supa fly bolt and shocktech rat valve
good low pressure use
not as good as it seems, way too much!! Really big
All in all this is a good front reg but I found the shocktech reg too be a lot better. The shocktech got the same pressure as with my evo LPR. The cost is really just big problem about buying it (100 bucks?) Get the Shocktech Reg its just as good and costs 40-50 dollars less. IF you want to watch your wallet. *Shocktech reg is good if you want to run your gun at 300 psi with good shot to shot consistency but the evo/belsales LPR can run very low i don't know but my tank sure as hell gets a lot more shots and my gun has great consistency too.
I love their barrels like the freak kit best kit out there!
Go with the shocktech if price is an issue but if you want a great piece of work get the Belsales LPR
Mine was defective something messed it up during shipping so it wasnt the regs fault I have a new one now and it is great. so instead of 8 I give it a 10
10 out of 10
Last edited on Sunday, November 23rd, 2003 at 6:45 pm PST
2k2 Vert. Glacier-Ize freeflow cocker, 8 hole freeflow bolt, 2k3 sto ram, belsales 2 stage reg, stock sledgehammer with belsales twister cap and custom settings, stock wgp, vert reg-psi set to the lowest at 270'ish, stock 3-way, phsyco drop with a blue macro, 48ci 3k psi nitro. Ans quickfire slider at 2mm trigg. pull.
very nice, no doubt bout that
eh.. i'll explain in review
all in all, this reg is different. Ok but, i'm putt a different reg on this post. It's still the belsales, but it isn't the evo. reg.. well i guess it is. But it has a 1st stage. The belsales i have is a 2 stage reg. Which, there are 2 pieces that comes off. There's the back end of the reg which screws off to fine tune the reg. Then there's the front twister cap. Ok, the reg is good. But get's annoying when you try to perfectly make your cocker lp. So i found a new discovery. Sledgehammers are REALLY GOOD! i don't understand why people dump'em once they get their cocker. If you take off your sledge hammer, u unscrew the female/female screw that is screwed into the back side of the reg, and the other side screws into the front block. there might be locktite, unsure about that. Mine didn't it will have a thick o-ring which sorta makes it tough to take it off. Once you take it off, There is a tiny silver screw. Ok.. shhhh... This sorta breaks the "concept of wgp" with changed "their preset psi adjustment." But.. OH WELL! my cocker. my sledge. i'll do wut ever you want. If you take a flat head screw driver, and screw the silver screw clock-wise into the reg...i'm still unsure, since i'm studying this.. i think it most likely decreases the pressure. But DON"T screw it in until it doesn't screw, only a couple times. THEN! on the cap of the sledgehammer there's no rock. But it's ok, unscrew safely the nipple where the hose goes onto. once that's unscrewed, you, take a towel, yet pretty thick, then take a monkey click wrench. That wrench is the kind when, there's a screw on the bottom, so when you hold the grips really tite, it'll lock in place so that setting doesn't move around, then press the little lever to un click which opens the wrench back up. ok, so unscrew the stock flat cap of the sledge, then -takes deep breath-.... then take the Belsales Front Twister cap and screw it on. There you go... The Belsales Front Twister cap with rock is only like.. wut... $20? here, u have a pneumy reg... that's BETTER then a palmers... better then ans...
If you read my other forums, you'll see that i am a cocker/spyder specialist.. which is why..... ..... i virtually know every single aspect of both genre of guns. Over all the Evo and the Belsales 2 stage reg are BOTH GOOD! Email me, if u have any questions. I would love to help out and answer questions.