pbReview.com / New Designz Super Short Bolt / New Designz Super Short Bolt / New Designz Super Short Bolt / New Designz Super Short Bolt / New Designz Super Short Bolt
No o-rings, never requires lube
Actual field tests show an increase in velocity of 12-30fps over stock with some nearing 30+ fps during initial HPA tests
Greatly improved consistency, you may think the chrono is not reading
Efficiency increases up to 36%, 27% over some other aftermarket bolts (Varies from marker to marker)
Allows you to lower input operating pressure and or decrease your dwell
Delrin bolts do not wear the Impulse body like the stock aluminum bolt. Specific sections on the bolt are slightly smaller to decrease even more friction. Look closely..
High flow port design to stabilize the air with an ultra smooth surface finish
The Equalizer chamber between the bolt and the ball is designed to displace air pressure over the whole back surface of the ball with the increased volume area and not just 6 holes
Angled air inlet port for the best possible air flow, efficiency and less turbulence
A stock length bolt weighs only 29.5g while this stubby is a mere 19.3g - considerably less than the aluminum one at 54.6g allowing faster cycling due to less inertia
Improves accuracy by decreasing recoil while providing a quieter shot
Also, don't be surprised when you go chrono and the alarm sounds, you'll be shooting hot
Product Availability
The New Designz Super Short Bolt is older, so while it may be available used and in a few cases new, it is not commonly available anymore.
Places to Buy
No Stores
Sponsored Links
Write a review and share your thoughts with other paintballers.
Impulse
New Designz Blade Trigger
New Designz stubby bolt
New Designz ss rat hole
New Designz slick shot ram
New Designz rip valve
Check-It no rise
jackhammer 2 lpr
Evo2
45/45 pe tank
Strengths:
High Flow, Light weight
Weaknesses:
its nd weaknesses dont exist
Review:
This bolt is incredible
when i first got it i didn't think it would fit in my impulse well but i was wrong. it actually slides in and out pretty easily so i don't have to use a squeegee or anything to take it out.
when i first looked at it i realized that the air flow was much better then the stock. the holes in front are also much bigger.
this is a great product. and since its so light it will help you balance your internals better
Weighs 300 grains, 3 Very large air flow ports, perfect to help balance your internals.
Weaknesses:
it's from New Designz, they don't know how to make a bad product.
Review:
First off, this thing is so light I thought I might break it by holding it, it weigs in at 300 grains. Like I said earlier, perfect for balancing your internals.
Second, the bolt face has three Massive air flow holes for maximum performance, it is so close to being an open faced bolt it's great.
Third, accuracy is this bolts bread & butter. I have had or used all the bolts I can get ahold of and this bolt is king of the hill bar none.
Fourth, this bolt is so well thought out that the design is amazing. For instance, they put a little ball detent in the back to keep the pull pin in place rather than put a stupid bubble sticker on the back, brilliant!
Conclusion:
it is light, fast, accurate, and very well built. Bottom line: if you have major milling done, or are considering it this bolt will fit the milling and be a reliable bolt for years to come. just don't look for colors, as it is only made in black at this time.
Spyder Imagine LED
12" Teardrop Barrel
Shocktech Superfly Short Bolt
Diablo Halo LED Front Man TSA Paintball Loader
16 Oz
Strengths:
Delrin
Nice quality
Weaknesses:
No weaknesses found.
Review:
I bought this bolt because the stock bolt on my Spyder Imagine LED chopped everything, jammed, uncocked and I was tired of lubricating it. This bolt fixed all of those problems. It made my marker faster and it was easy to install. The only little problem was that I had to file down the back of it so it wouldnt scratch up the body of my marker. The indent in the front of the bolt was nice, like the description said, it cradled the ball instead of hitting it with a flat surface.
Conclusion:
Overall I would reccomend this bolt for every marker it will fit in. Its fast, delrin, and nice looking.
vision impulse
half backed
lapco lowrise
new desighnz bolt
all american
eclipse magno trigger
Strengths:
Doesnt need 2 be oiled
Weaknesses:
None
Review:
I really like it i have a milled impy so the last half an inch sticks out when cocked back it never needs 2 be oiled it is nice i have had no problem with it but i can imagine that if u did not have a milled impy iy would be hard 2 get out
2004 Smart Parts Impulse
Nerve clamping feed neck
Egg II
20oz anti-syphoned/on-off valved tank
NDZ Super short bolt
Strengths:
Small
Light
Requires no lube
no o-rings
Weaknesses:
Size- bolt can be hard to remove/replace on non milled imps
Review:
Alright,
I got this to replace the stock bolt, which weighed a ton and needed that expensive DOW 33 lube. Also, I believed it would Increase my cycle speeds.
I got onto the field and I noticed a huge increase in the "smoothness" of operation, and there seemed to be less "kick" and a noticable decrease in noise. After shooting about 500 rounds the first game, I chopped a ball because my egg doesnt seem to feed the non-vision impy fast enough. I pulled out the bolt, wiped it off, and re-inserted the pin- it was that simple. You may ask "Your just cleaning the bolt, why is it so important?" Its important because I was able to wipe off all of the paint in one pass of a towel. With the stock bolt, you had to make sure all of the o-rings were clean of paint. So, the derlin helped in the area of field stripping.
Speed Increase?--- No. That could be because I have a non-vision impulse, and after about 7 BPS, I chop. So, ill update this review when I get eyes in about two weeks.
Efficiency Increase--- Somewhat, not somthing you can really notice though. I probably got about 30 more shots out of my 68/45 tank.
Conclusion:
Im impressed with what $30 can do for my impulse. Even though there wasnt really a performance change, the ease of cleaning the bolt's surface after a chop was a real advantage. Id recommend this bolt if you had a milled body, because getting the bolt back in the gun can be somewhat challenging.
Final rating- 9/10 because of the extreme shortness.
2004 black imp
ndz stubby bolt
all- a 14 in.
strange ram and hammer assembly
red halo b
68/3000 nitro duck
Strengths:
Size
Weight
Efficency impovement
Weaknesses:
Kinda hard to get out of gun if your hands are wet or greassy
Review:
well this is one bolt that is well worth trhe money. This bolt combined w/ the strange hammer gave me a 30fps jump in velocity and about 900 shots of my tank instead of about 750. It is the best imp bolt on the market and is perfect for the gun.
2k4 vision impulse, new v3 i-frame, nd white stubby, nd lpr, shocktech regulater.
Strengths:
Short
Barely weighs anything
Made my gun fast with no shoot down
Better volocity
Weaknesses:
I have the white one and it gets dirty from lube but easy to clean.
Review:
When i got this bolt i was surprised by how small and light it was. When i actually shot it with paint, this thing ripped!!!!! When i actually got to the field i put my bolt in and aired up my gun and put paint in it. This bolt fixed my fsdo problem. but I ripped a huge string with no shoot down. i got tons of compliments of how it shot from some team members.
