|
|
pbReview.com / A+ Anodizing EGO Bolt / A+ Anodizing EGO Bolt / A+ Anodizing EGO Bolt / A+ Anodizing EGO Bolt
A+ Anodizing EGO Bolt Reviews
|
|
|
|
Number of Reviews: |
1 |
|
Average Rating: |
9.0 / 10 |
|
Manufacturer Website: |
Click here |
|
Suggested Retail Price: |
$45 |
|
|
|
An all delrin bolt that has two o-rings and a stainless steel pull pin including
Gives at least 10% better gas efficiency (More shots per tank)
Gives at least 10% better gas efficiency (Less air pressure needed)
10% Better velocity consistency (Less Chrono penalties)
Better Accuracy (More eliminations)
Ball Detent slots (Won't wear out Ball Detents)
|
|
| Product Availability | |
|
| The A+ Anodizing EGO Bolt is newer, so it should be commonly available, both new and used. |
|
| Places to Buy | |
|
|
|
|
|
|
Period of
Product Use: |
| Only tested | 2 of 2 people found this review helpful.
|
|
|
Paintball
Experience: |
1 year |
|
Similar
Products Used: |
Stock Ego bolt |
|
| Marker Setup: |
P.E. Ego
Stiffi barrel
Hybrid trigger
Hybrid adjustable RAM cap
Empire Reloader B
Empire Fuel 46/4500
SP Ion w/ Blackheart board
Halo B
CP: HP reg, rail drop & 2k5 on/off
Dye UL barrel & St!ffi Switch Kit
BT APEX barrel |
|
|
|
|
| Strengths: |
O-rings |
|
| Weaknesses: |
Not lighter than the stock bolt as stated |
|
| Review: |
Overall this is a nice bolt, at first I thought it was a little stiff when I moved it back & forth but after I lubed the o-rings and rammer I went outside and I easily ripped 15bps.
The o-rings should give you a better seal when shots are being fired & I noticed even less blowback (when feeding a couple of paintballs directly into the feedneck, when you shoot they jump less)
The little bit of kick is about the same as the stock bolt because when I weighted each bolt, they both came in @ 1.4 ounces.
The claims of an efficiency increase can be true because you can decrease your dwell and probably lower your LPR pressure as well as lower your HPR input, so you're blowing out less air when shooting,.............with properly lubed o-rings you should have even less friction than the stock delrin bolt becasue of a lesser contact point between the guns' insides & the bolt.
The groove for the ball detent are a bit longer than the stock bolt so that might increase the life of your detents.
I ordered a delrin pull pin to hopefully reduce the bolts' reciprocating mass, so it should also reduce kick....I also ordered teh NDZ bolt so I can compare the stock, A+ and NDZ bolts.
I got the delrin pull pin which reduced the bolts weight to 29g, about 1.1 ounces...so it has a bit less kick now than before.....it sounds like its shooting fast but I know this is not true.
The A+ bolt does not have a way to tighten the pull pin ball stop |
|
| Conclusion: |
Nice bolt with o-rings....it's not lighter but the o-ring design should give you a better seal when the shot is fired...not bad, not bad at all....I will continue to use this bolt and see if any issues come up. |
|
| Rating: |
| 9 out of 10 | Last edited on Monday, January 2nd, 2006 at 3:46 pm PST |
|
|
|
|
|
|
| Places to Buy | |
|
|
|
|
|
