a-5, e-grip, expansion chamber, double trigger, 32 degrees drop forward
This product makes your gun have a clean look, and does its job as expected
Iv used this product many times about 7 to be exact and i have no problems I read all the reviews on this product and have found most of them to be over exaggerated or the person has very bad luck. I installed this product not know exactly what I was doing and all the connections were successful. I have no leaks or breaks after 7 days of play
I recommend this product cause it does the job well is flexable, and gives a clean look to your marker.
10 out of 10
Last edited on Monday, January 10th, 2005 at 5:40 pm PST
Spyder Victor With ACI Subzero Xchamber, 14" teardrop, Classic CAMD E-frame, ACS Delrin bolt.
Cheap, Flexible, fits any setup.
Breaks easily. Co2 will rip through it.
Don't buy this macro line kit. Its crap. I set it up correctly with no sever kinks or bends in the hose, the ends were flat and clean cut and all the adapters were air tight. I gassed it up for the first time and the line looked good. No less than 5 minutes later, the line blew. This is on HPA mind you. So I cut a new length and gassed it up again. This time it took a game or so before it blew. At that point i said screw it and went back to steel braided hose. I gave the rest of the kit to my friend because he wanted to try it. He set it up and it blew the instant he gassed up. Possibly becuase he runs CO2.
Steel braided hose is by far a better buy than this kit. for less than $5 US you can get the hose size you need. Don't buy this kit.
2 out of 10
Last edited on Thursday, April 14th, 2005 at 12:50 pm PST
Nothing really...I always used steel braid...probably still will after this fiasco
Milsim 98 Custom
None that I have found
Weakness being the key word...It goes POP very easily
I am not sure what the pressure rating on this macroline is but it is definately not enough for an Automag. I tried to run about 900-1000 psi into my new Tac-One to enjoy some trigger bounce and POW!!! Blew a macroline. This stuff is weak.
It works fine at about 800psi....but not 900. That is a little too close for comfort when I need to run at least 800-850 to get the gun to work properly.
If you are using a low pressure marker this stuff is probably fine. But for you guys (like me) that need to run a marker at high pressure (850psi). This is not for you. There is a reason this stuff is so cheap. And I think it is because it is junk.
The accuracy of this review is disputed. Please see discussion on the comments page.
Period of Product Use:
Less than a month
0 of 2 people found this review helpful.
Similar Products Used:
braided steel hose....lots better and safer...other macroline
Tippmann A-5-Smart Parts Progressive barrel-DOP X-Core 8 stage expansion chamber
Ok i bought this kit because I ordered my expansion chamber and b/c of its ease of installation. If I had read the reviews on this site before purchasing the kit, I would not have done so. This macroline kit by 32 Degrees is the worst macroline kit I have ever seen. Just like a few reviews say above this kit is VERY unsafe and should be taken off the market or improved to where its not so unsafe. 5 minutes or less before I was about to enter a game at a friends field the hose blew out the bottom...not out a a fitting or anything like that..the co2 blew a hole in the actual hose spewing out a full 20 oz co2 tank. I think this is the most unsafe product I have ever bought and will be calling 32 Degrees to get some kind of compensation or hear what kind bs they have to say about it.DO NOT BUY THIS KIT
read above...this product would have a zero...if possible
Black Model 98 Custom (polished internals and silenced bolt)
20 ounce Atomic Energy CO2 bottle with anti-syphon (and APP Butt plate)
DYE 12" Stainless Steel Barrel
Adco Sure Shot Red Dot Sight
6 stage X-chamber
LAPCO rear velocity adjuster
empire reloader agitated hopper
Good if you're putting an x-chamber on
mine leaks a little at the elbows
Leaks a little at the elbows, but is easily fixed by playing with the tubing (pushing it in more) and sometimes screwing it in tighter with a wrench. I'm running Co2 on my setup; and it works fine once you kill the leak.
Overall I don't know who also makes macro line; but they probably make better ones than 32* since its a pretty cheap company. I'm using mine on a rec-ball tippy; so I'm not as finicky.
Does its job, even if it has an easily fixed leak.