pbReview.com / New Designz High Flow Valve / New Designz High Flow Valve / New Designz High Flow Valve / New Designz High Flow Valve / New Designz High Flow Valve
Looking to blow your competition away? Well this valve will set you on your merry way. Machined from aluminum and Delrin, making this a lightweight but also a highly reliable choice.
Radial intake port profile
Angled exhaust port for maximum air flow
Internal spring for no disruption of air flow or lost springs
Initial tests show and increase of 15fps from a stock valve and 40+fps on an LPR setup Imp. 140psi inlet, 60psi bolt pressure.
Our valve weighs only 17.6 grams, w/O-rings
Our Delrin valve has a small surface area which makes it easier to open
Comes complete as shown w/ O-rings
Product Availability
The New Designz High Flow Valve is newer, so it should be commonly available, both new and used.
Places to Buy
No Stores
Sponsored Links
Write a review and share your thoughts with other paintballers.
2003 impulse, evil pipe barrel,KAPP IP3 'brass' hammer,ND bolt, flame drop forward+off on switch, ND valve cap, ND RIP valve, ANS LPR, and magnetic trigger and or ND fully adjustable trigger {testing ND trigger against the Magnetic}
Strengths:
found a increase of 35fps. I now run at 140psi dwell at 8. Lighter!
Weaknesses:
seems like the valve has no protective coating, though it could be clear? Grease it
Review:
I'm very familiar with the disassembly of the marker and found the valve to be very easy to install, though you do have to take it apart quite a bit to get the valve in. The New designz valve is Much more efficient than the stock valve as seen in the fps result of +35. I get 294fps out of the current settings of max flow at 140, 8 milli secs of dwell.
Running the gun without the LPR and tape worm and with the stock valve cap I see 280 fps with setting of 120psi and 6. milli seconds of dwell. NEW Designz Bolt and rip valve... are great for low pressure and air efficiency
Conclusion:
GET one NOW! if your serious about your paintballing. Cheap addition that makes a good gain in performance.
Rating:
10 out of 10
Last edited on Monday, June 9th, 2003 at 1:51 pm PST
Nothing compares with this valve. This one rocks the house!
Marker Setup:
2002 Vision Impulse with new designz low rise, new designz high flow valve, new designz delrin bolt, new designz titanium bolt pin, new designz slick shot ram shaft, michigan paintball outlet stainless steel rat hole hammer, new designz high volume valve cap, new designz blade trigger, dye sticky grips, eclipse solenoid optimizer, and a new designz hammer cap.
Strengths:
-Super high flow
-No valve spring
-Bumps fps +20
-Reduces dwell
-Reduces internal pressure
Weaknesses:
-Pain to install
Review:
This is hard to install, but once it's in, you've got quite an impulse. My fps went up 50fps, and I don't even use an lpr. My impulse runs at 120psi, with very little dwell. Increased my air efficiency, reduced kick, and it's one more part I don't need to lube anymore! Plus, no more valve spring!
Conclusion:
A must have for any impulse owner. Only hard to install, but it pays off!
Impulse
10" Freak, Dye grips, Wermstick trigger,
ND HVVC, ND hammer cap, ND equalizer bolt,
ND high flow valve, tape worm, CP drop forward,
Eclipse anti double ball.
Strengths:
This valve is awsome! A must buy for all impy owners. The first thing I noticed about this valve was that before, using my stock valve, I shot 250 fps running at 180 psi on my max flo. When I used this valve I had to turn my pressure down between 140-150 psi. Its way more efficient than the stock valve. Also its very easy to install.
Weaknesses:
The only thing that was a little bit bad was that I had a little bit more bolt stick(due to the low pressure) but I bought a tapeworm and adjusted the dwell and all was great.
Conclusion:
This valve is all of what they say on the New Designz website and more.
